Because of the emergence of the wall plastering machine, it has replaced manual wall plastering. It is very convenient to operate. It can save time and manpower. At the same time, the quality of the wall plastering is very good. The most important thing is that it is very safe and reliable. Reduce the occurrence of accidents. So do you know how the wall painting machine works? What is the principle used? If you want to buy a wall painting machine, which manufacturers can you choose?
Principle:
1. The problem of weak positioning is solved by hydraulic jacking and grounding, and the positioning is fast and can be fixed vertically and flatly in about 10 seconds.
2. The use of two supports combined with traditional dotting solves the problems of slow laser positioning, difficult positioning, and large errors.
3 Using a vibrator to enlarge the plaster board solves the problem of hollowing and cracking in manual plastering of walls. The maximum plastering thickness on water-absorbent walls can reach 3 cm, and the minimum plastering thickness is 0.3 cm.
4. The use of a trowel that can change the angle solves the problem that the machine cannot descend along the original path for calendering.
5. The working surface of the machine is 80 centimeters wide. If you wipe 80 or 80 centimeters of a wall and the remaining 20, 30 or 50 centimeters are left, you only need to fill one side, without adjusting or blocking. Because it has been in the sand and dust for a long time, any adjustment or blocking is impossible.
6. The conveyor belt of the breakthrough wall plastering machine can be stopped alone. For example, after passing the construction hole and then feeding the ash, it can plaster above the construction hole.
7. Use the matching limit clamp and clamp it to the same height as the lintel to wipe the bottom of the lintel. In the same way, use both hands to press the two sticks that change the angle of the wiper to the bottom of the window, and you can wipe the bottom of the window.
8. The wiping plate is designed to be wider than the fuselage, so the inner and outer corners can be easily positioned.
Operation steps of the wall painting machine
Dot the wall (the middle point is 1.6m from the ground, the bottom point is 400px from the ground, and a point is made every 1.5m)? Do it one day in advance.
Water the wall (brick wall). Do this one day in advance
Measure the height of the room and add appropriate joints. (The vertical poles in the machine are designed to cover the room height of 2.85 meters. If the room is high, corresponding joints must be added)
Install the vertical poles. (Two people install, make sure the threaded link is flat)
Install the handle. (The handle is divided left and right)
Connect the power supply. If the power indicator light is always on, it means the three-phase power supply is correct. If the light turns on once and then goes out, the power input is reversed
Click up button to raise the machine pole 1-50px from the ceiling
Lock the hydraulic pressure and pull up the handle
Position (one person holds the middle bar, the other holds the support and steps on the hydraulic pressure)< /p>
Step on the hydraulic pressure, the vertical pole rises and presses against the ceiling, and the machine is fixed.
Add ash, click the start button and the machine will rise
After the machine reaches the top, vibrate for 5-7 seconds, turn off the power, then turn on the power again, the machine will drop and calender the wall.
After the machine reaches the bottom, release the hydraulic pressure
Click the drop button (it will suffice to drop 50px), and the vertical pole will drop.
Move the machine (make the machine plaster board close to the wall and translate the machine) so that there is a distance of 50px between the two walls.
Reposition and work on the second wall.
Clean the machine in time every day after use. Disconnect power before cleaning.
The hopper board and vibrator parts should be flushed directly with water pipes. It is forbidden to flush the machine panel with water and can only be wiped with a cloth.
Advantages of the wall painting machine:
Advantage 1: The problem of weak positioning is solved by using hydraulic jacking and grounding, and the positioning is fast, only taking about 10 seconds. Can be fixed vertically and flatly.
Advantage 2: The use of two supports combined with traditional dotting solves the problems of slow laser positioning, difficult positioning, and large errors. ?
Advantage 3: The conveyor belt is used to transport ash forward and upward in combination with the large wiping plate that can change the angle. It can be completely wiped to the top without leaving a millimeter.
Advantage 4: The use of vibrators to enlarge the plaster board solves the problem of hollowing and cracking in artificial plastering walls. The maximum plastering thickness on water-absorbent walls can reach 3 cm, and the minimum plastering thickness is 0.3 centimeter. ?
Advantage 5: The use of a wiper plate that can change the angle solves the problem that the machine cannot descend along the original path for calendering.
?
Advantage 6: Using the pull-out rod makes it easier for you to dock freely at different heights. It also solves the problem that the telescopic rod cannot pass through the construction hole. Moreover, when the machine is on the construction site, it can be used by plugging in the vertical rod. , no assembly required. It can be transported by removing the pole, no disassembly is required. ?
Advantage 7: The conveyor belt of the machine can be stopped alone. For example, if the ash is delivered after passing the construction surface, it can be applied above the construction surface. ?
Advantage 8: The smallest side of the machine is only 60cm wide and weighs 98kg, so it can be used even in a small bathroom at home. ?
Advantage 9: Use the matching limit clamp to wipe the lower part of the lintel when it is clamped to the same height as the lintel. In the same way, use both hands to hold down the two sticks that change the angle of the wiping board to the bottom of the window, and you can wipe the bottom of the window. ?
Advantage 10: The wiping plate is designed to be wider than the fuselage, so the inner corner is easily in place, and the outer corner is in place on one side. ?
Ren County Jiacheng Machinery Factory
Wall plastering machine, plastering machine, wall painting machine, fully automatic wall plastering machine, new fully automatic wall plastering machine
Minimum quantity: 1 unit
Price: 500 yuan
Xingtai Jinqi Machinery Manufacturing Factory
Specializes in the production of wall plastering machines/automatic wall plastering machines/water Silt ash plastering machine/wall dust spraying machine
Minimum quantity: 1 unit
Price: 300 yuan
Xianxian Quangda intelligent wall plastering machine equipment Factory
Automatic wall scraping machine, automatic wall plastering machine, new wall plastering machine
Minimum quantity: 1 unit
Price: 16,800 yuan
p>
The above is an introduction to the working steps and principles of the wall painting machine. The manufacturer's recommendations and prices are for your reference only. For details, you can contact the manufacturer directly. With the wall painting machine, people no longer have to climb to high places to work, nor do they have to worry about safety issues, let alone the poor quality of the wall due to human errors, which greatly simplifies the construction project. The editor here reminds everyone that no matter how good the machine is, people must take good care of it, so as to extend its service life and continue to provide convenience to us.
Tubatu provides you with "each decoration quotation, 1-4 local decoration companies, 3 sets of decoration design plans" online for free, as well as decoration avoidance strategies! Click this link:/yezhu/zxbj-cszy.php?to8to_from=seo_zhidao_m_jiare&wb, and you can get it for free~