Product features and technical level of the refiner: The height of the fuselage is 63CM, and the diameter of the fuselage is 23CM FDM- 100+000. A number of national special technologies have been invented and applied, which has changed the disadvantages of similar products such as low efficiency, high energy consumption, difficult cleaning and disassembly, and many wearing parts, and made a major breakthrough in technical performance, mainly as follows: 1 2. Patented technology of grinding wheel positioning device of refiner makes the machine reset accurately after repeated use and run stably and reliably. It takes only 2-3 minutes after each operation to disassemble-thoroughly clean-reassemble and reuse. It can prolong the service life of the main component-filter screen frame by 5- 10 times. 3. Patented technology of static grinding wheel connection device of refiner saves time and labor by replacing static grinding wheel, which can prolong the service life of the main component-grinding wheel seat by 5- 10 times. 4. Unique overall design and surface treatment technology make the machine compact and reasonable in structure, durable, exquisite in appearance, sanitary and clean. 5. The application of the adjustable feeder technology of the refiner makes the performance of the refiner better. Under the voltage of 180V-240V, it can properly operate soaked soybeans with different particle sizes and hardness. This product has won many honors at the national, provincial and ministerial levels. The performance of the whole machine is at the leading level in China, and its main technical performance has reached the international advanced level. FDM-Z 100 self-separation slag crusher is widely used to soak beans, rice, miscellaneous grains, dried potatoes and make tofu and starch. Removing the filter screen can grind the pulp of pancakes, cakes and other foods. Operating instructions 1. Soaking materials: firstly, remove impurities such as iron, sand and stones from the materials; Soak in warm water until there is no hard core. (Note: Soaking materials with high-temperature water will easily lead to high viscosity and poor slag separation effect). 2. Start: loosen the lock nut and adjust the handle to rotate in the rough direction until the filter screen frame exposed from the slag outlet is gently pushed out by hand, and the motor can be flexibly started. (The rotation direction of the three-phase motor should be consistent with the logo on the cover, otherwise it should be stopped immediately, and two of the three phases should be replaced and restarted. 3. Adjust the gap: adjust the handle in a thin direction until a slight rubbing sound is heard. Don't adjust it too fine. If it is too fine, it is easy to grind the bean skin and block the mesh of the filter screen, resulting in slurry in the slag, which obviously reduces the production efficiency and increases the power consumption. The gap is too large, and the slag yield is too high, which also causes low productivity and waste of materials (empirical data is per kilogram of dry soybeans; Soak about 2 kg, and add about 2.5 kg of water when operating; When the weight of wet slag is about 1.3 kg, the soybean milk concentration, slag yield, output per hour and separation degree are the best. In order to further improve the utilization rate of bean dregs, bean dregs can be made into porridge with water, put into a hopper and processed repeatedly. Use of 4.CA/CB-type adjusting piece: When the processed material is soft or the particle size is large, the productivity is low, and the motor load is light, loosen the fastening bolt to separate the positioning cam from the positioning cam, rotate the adjusting piece, increase the feed inlet of the puller to a suitable position, and make the positioning cam fall into the positioning hole, and tighten the bolt to increase the feed rate. When the material to be processed is hard, the particle size is small, the blanking is too fast or the voltage is too low, and the motor is overloaded, loosen the fastening bolt, make the positioning nipple separate from the positioning hole, rotate the adjusting piece, lower the feed inlet of the puller to a proper position, make the positioning nipple fall into the positioning hole, and tighten the fastening bolt to reduce the feed. 5. Cleaning: After the work is finished, the filter screen and residues in the machine should be cleaned in time to ensure good slag separation effect and sanitation in the machine. The method is as follows: 1. Unscrew the fastening bolts on the puller, and remove the screen frame and movable grinding wheel. Carry out cleaning, and the filter screen must be cleaned until there is no blockage. 2. Wipe the inside and outside of the machine with a rag, and do not rinse with water to prevent water from entering the motor. 3. Refer to the structural drawing to restore the filter screen frame and other related components in turn, and fasten them with fastening bolts; Get ready for next time.
For refineries. Logistics (freight) is delivered in any region, and the freight generated in different regions is different. Please contact us before shooting. 1, soaking materials: firstly, remove impurities such as iron and sand from the materials; Soak in warm water until there is no hard core. (Note: Soaking materials with high-temperature water will easily lead to high viscosity and poor slag separation effect). 2. Start: Loosen the lock nut and adjust the handle to rotate in the rough direction until the filter screen frame exposed by slag is gently pushed out by hand, and the motor can be started after flexible rotation. (The rotation direction of the three-phase motor should be consistent with the logo on the cover, otherwise it should be stopped immediately, and two of the three phases should be replaced and restarted. 3. Adjust the gap: adjust the handle in a thin direction until a slight rubbing sound is heard. Don't adjust it too fine. If it is too fine, it is easy to grind the bean skin and block the mesh of the filter screen, resulting in slurry in the slag, which obviously reduces the production efficiency and increases the power consumption. The gap is too large, and the slag yield is too high, which also causes low productivity and waste of materials (empirical data is per kilogram of dry soybeans; Soak about 2 kg, and add about 2.5 kg of water when operating; When the weight of wet slag is about 1.3 kg, the soybean milk concentration, slag yield, output per hour and separation degree are the best. In order to further improve the utilization rate of bean dregs, bean dregs can be made into porridge with water, put into a hopper and processed repeatedly. Use of 4.CA/CB-type adjusting piece: When the processed material is soft or the particle size is large, the productivity is low, and the motor load is light, loosen the fastening bolt to separate the positioning cam from the positioning cam, rotate the adjusting piece, increase the feed inlet of the puller to a proper position, make the positioning cam fall into the positioning hole, and tighten the bolt.