Installation method:
Preparation before installation: electric drill, tape measure, chalk ... Let's take a look at the accessories including hand crank, handle, pulley frame, corner device, lifting ring, fixed cover, expansion screw, wire rope and socket. Find the installation position of the hand crank and punch it. It is suggested that the height of the hand crank from the ground should be 1M- 1.2M, and then the position of the corner crank should be determined. (Note: the position of the corner device must be perpendicular to the position of the hand crank, and the red circle is the installation position of the hand crank. )
Next, determine the positions of the four pulley frames: the distance between the two sides of the pulley frame and the wall is not less than 27CM, the vertical distance between the two pulleys is not less than 45CM, and the horizontal distance between the two pulleys is 18CM or 2M, which is generally 2 m. The specific pressing position depends on the actual situation of the household balcony. After the installation position is determined, use the pulley frame to determine the punching position. Next, install expansion screws on the pulley frame: one ***4, two single pulley frames and two double pulley frames. Similarly, install two expansion screws on the corner adjuster.
Next, install the hand crank: fix the hand crank with expansion screws, then tighten the expansion screws with tools, install the handle, tighten the screws on the handle, and then shake out all the wire ropes in the hand crank. When shaking out the steel wire rope, you need to pull the steel wire rope to avoid wire disorder until the handle can't turn (this function is unique to smart life and has anti-shake braking function), and pull out another steel wire rope in the same way, as above. Note: There are two wire ropes in the crank handle. Push the handle to control the left and pull it out to control the right.
Next, start threading the wire rope: open the package, which contains two steel wires with the same length. First, hold both ends of the wire rope and thread it into one of the corner devices. Then the two ends of the wire rope pass through one of the double pulley frames, and the two wire ropes are parallel and not wound. Pull one end of the steel wire rope passing through the bottom of the double pulley frame to the position close to the crank, and the other end passes through the corner device. The operation method of the other wire rope is the same as above, and then hang the button at one end of the wire rope that is shaken to the corner by the hand crank. Install the fixing cover. Next, put two long wire ropes on the double pulleys on the other two single pulleys, and also install the fixing cover. Next, cut the four ends of the wire rope flat, the height is about above the handle, then install the lifting rings, then put four lifting rings on the two ends of the two air-drying rods, and then put the stoppers on the two ends of the air-drying rods, thus installing the air-drying rods. Install the last two sets of small accessories, so that the whole drying rack is installed.
Recommended brand: Good Lady Double-lever Hand Dryer
Appearance and size:
The appearance of this aluminum-titanium manual double-rod hanger adopts the latest special polishing technology, which makes the surface feel quite delicate, shiny and emitting noble light. The simple style with silver tone does not lose the atmosphere, and the goddess of high value. The length of the two rods of the clothes hanger was measured on site, which basically met the standard size of 2.4m, and the error was within the allowable range.
Materials:
The drying rack shaft is made of aluminum-titanium alloy, which has light weight and good hardness. Equipped with genuine 304 stainless steel wire rope, it is more durable. The quality of pulley directly affects the lifting of clothes rack. Pure copper composite pulley, smooth and durable without rust. Therefore, mother no longer has to worry about the problem that the weather is humid and it is easy to rust after long-term contact with water.
Durability and flexibility:
The clothes drying rod is the main part of the clothes hanger, equipped with stainless steel wire rope, which is more durable and has high tensile strength. This hanger can bear up to 35kg, and it has good bearing capacity, so you don't have to worry about crushing overweight clothes. Good wife patented hand crank, unique automatic gear shifting function, easy gear shifting, as convenient as automatic car rocking control, through push-pull swing conversion, respectively adjust the height of two bars.
Above, we introduced some knowledge about hand-cranked clothes hangers to you. Many families probably want to buy a hand-cranked hanger, but they don't know which brand is good. So this article will recommend a brand of clothes hangers for everyone. We introduce this brand of clothes hanger from the aspects of appearance size, material, durability and flexibility, and everyone will face installation problems after buying it. In this paper, we also introduce the installation of clothes hangers in detail, so that users can read them carefully.
Tubatu Online provides you with "every decoration quotation, 1-4 local decoration companies, 3 sets of decoration design schemes" and the decoration pit avoidance strategy for free! Click this link:/Zhu Ye /zxbj-cszy.php? to8to _ from = SEO _ zhidao _ m _ jiare & amp； Wb, you can get it for free ~