First of all, the laser head does not emit light.
1. Press the test key on the operation panel to check the current meter status:
① No current: check whether the laser power supply is connected, whether the high-voltage line is loose or off, and whether the signal line is loose;
② Current: Check whether the lens is damaged and the optical path is seriously deviated;
2, check whether the water circulation system is normal:
① Stop water supply: check whether the water pump is damaged.
② Water supply: check whether the water inlet and outlet are reversed or the water pipe is broken;
3. Yes, it can be self-checked, and the transmitted data does not emit light (check whether the computer settings are correct).
Second, the carving depth is different or the carving is not deep.
1. Check whether the water in the water circulation system is unblocked (whether the water pipe is bent or broken);
2. Check whether the focal length is normal (recalibrate);
3. Check whether the light path is normal (recalibrate);
4. Check whether the paper laid on the board is too thick and whether there is too much water (recalibrate);
5. Check whether the beams are parallel (adjust the belts on both sides);
6. Check whether the lens is damaged (replaced);
7. Check whether the lens or the emitting end of the laser tube is contaminated (re-cleaned);
8. Check whether the water temperature is higher than 30℃ (replace the circulating water);
9. Check whether the laser head or focusing lens is loose (tightened);
10, the laser current intensity must reach 8ma；;
1 1, laser tube aging (replacement: no charge during warranty period);
Third, the reset is abnormal.
1, check the sensor for dust, poor contact or damage (wipe off the dust on the sensor or replace it);
2. Check whether the data cable of the flexible conductive tape is in poor contact or damaged (trim the data cable, plug it in again or replace it);
3. Check whether the grounding contact is reliable or whether the high voltage line is damaged (re-grounding or replacing the high voltage line);
4. The motor wire is in poor contact.
Fourth, there is a leak.
1, incorrect initialization, data sent (corrected);
2. The operation sequence is reversed (re-output);
3. Electrostatic interference (check whether the ground wire falls off);
Five, cleaning hook edge dislocation, not closed.
1, whether the edited file is correct (re-edited);
2. Whether the selected target exceeds the layout (re-selection);
3. Check whether the software parameters are set correctly (reset);
4, the computer system is wrong (reinstall the operating system and software);
5. Check whether the tightness of the left and right belts is consistent or whether the rear belt is too loose (belt is too tight);
6. Check whether the belt or synchronous wheel slips and jumps (tighten the synchronous wheel or belt);
7. Check whether the beams are parallel (readjust the left and right belts);
Six, the computer can't output.
1, check whether the software parameter settings are normal (reset);
2. Whether the engraving machine is started according to the positioning before output (re-output);
3. Check whether the machine has not been reset (recalibrated) in advance;
4. Check whether the output serial port is consistent with the serial port set by the software (reset);
5. Check whether the grounding wire is reliable and whether static electricity interferes with the data wire (grounding again);
6, replace the computer serial output test;
7. Reinstall the software and reset the test;
8. Format the computer system disk and reinstall the software test;
9. The motherboard serial port is damaged and needs to be repaired or replaced.
Seven, the ultra-miniature engraving machine will not calculate the path.
1. Check whether the calculation method of setting the path is correct;
2. Check whether the graphic file format is correct (recalibrate);
3. Remove the software and reinstall the settings;
Eight, computer frequently asked questions
1, the font is gradually reduced (reinstall the operating system);
2. The amount of data is too large to calculate the laser path (wait for a while or increase the computer memory);
3. The calculation path has not responded for a long time, so restart the computer test.
Ji' nan weidiao weidiao laser weidiao technology
Service support laser engraving machine laser engraving cutting machine laser engraving machine.