1. The umbrella is separated from the pole. When the umbrella is opened automatically, the fixing pin is broken due to the elastic force of the spring, so that the umbrella and the rod are separated. Repair method:
① Replace the T-pin, and replace it with a flat iron file according to the original pin. When installing the pin, firstly flatten the directional inward protrusion of the upper umbrella pole, install the pin on the round holes of the handles on both sides, push the umbrella pole so that it exceeds the inner convex stalk, and then restore the inner convex stalk. At this time, close the umbrella and press the beginning, and the umbrella can be opened in sections automatically and unimpeded. Repeatedly, it will be repaired if it is no longer separated.
② use the iron wire with a diameter of 1 mm, refer to the original shape, fold and bend it into a T-shaped pin, which can also be used as a substitute. Pay attention to the clamping at the corner, and the whole pin should not exceed the groove of the I-bar, otherwise there will be resistance when opening the umbrella. The excess part can be leveled with a small file, and the installation method is as above.
2. fix the sliding hole of the pin, so that the pin and the umbrella can derail and slide out. When this kind of fault occurs, the T-pin is generally intact and can still be used. Repair method: add a thin copper sheet to the sliding mouth of the round hole, weld it firmly with tin, then repair the groove with a file, insert the T-pin into the round hole, put it back, and try to open it several times without error, and then repair it.
3. Hanging groove slide. The hook controlled by automatic switch can't be fixed after the umbrella is closed, and it often opens automatically. Repair method: cut a gap in the middle of the hook with a knife, which can look good when closing the umbrella, and can be automatic when opening the umbrella. The gap is large from small file, and the file is filed while trying until it is suitable.
How to repair the exposed white line of the automatic umbrella
Disassembly process:
1. First, spread the umbrella face down and clamp the pin with needle-nosed pliers. Hold the main pole hard during the process to prevent the main pole from popping up suddenly.
2 after the pin is pulled out, the main rod will pop out, and some main rod springs will not pop out. At this time, clamp the plastic head at the front end of the main rod with needle-nosed pliers and rotate it left and right to pull it out. During the process, the high-pressure spring may pop up at any time to hurt people. Pay attention to safety!
3 The white nylon rope is knotted and caught in the spring, so the main rod can't be retracted. Carefully loosen the spring by rotating it, and the spring will spring off by itself when it reaches a certain degree. Still need to pay attention to safety in operation
6 points for proper use of umbrellas
1. When opening an umbrella, first open the central rod * * * mainly folding umbrellas and straight umbrellas with drawable central rod * *, let go of the buckle and shake it left and right a few times, especially for light and short folding umbrellas, the umbrella cover and ribs should be loosened before opening, otherwise the skeleton will be easily broken, and the umbrella ribs of the two-fold umbrella should be HK bones when opening. This is easier to open. When opening an umbrella, you should also get into the habit of opening the front of the umbrella against the wind, because the support is fragile when the umbrella ribs are not fully opened in the opening stage. At this time, if the back of the umbrella, that is, the side of the umbrella ribs, is blown along the wind, it will easily cause the umbrella ribs to be damaged, especially for small umbrellas with three, four and five folds.
2. Fold the umbrella cloth according to the original crease, fasten the buckle belt, hold the umbrella with one hand, pat the bottom of the umbrella handle with the other hand, and pat the middle stick in, paying attention to taking it in, not pushing it in. Then, take the umbrella with both hands and spin it several times along the crease direction to make the umbrella cloth flat, and then screw it into the umbrella cover along the crease direction, paying attention to screwing it in, not inserting it. Besides, it is also a good habit to close the umbrella.
3. Before opening an automatic umbrella, be careful not to let the hanging rope hook the tailbone or break it when opening the umbrella. In addition, if it is an automatic umbrella, you should press the automatic opening and closing button to make the umbrella cover automatically close and then pull it back. Never pull the whole umbrella cover back and close without pressing the button, which will easily damage the automatic opening.
4. Don't break the umbrella cover with your hands after it is blown over by the wind. Just close the umbrella and open it again.
5. In the end, I still want you to remember a formula, which is: "Open against the wind and close against the wind!" This is a trick that I have summed up for many years. It is very easy to remember and practical. Everyone must memorize it, and do it according to the formula when using an umbrella at ordinary times. Over time, you will develop a good habit of using an umbrella and save a lot of troubles in repairing it. We must also explain this formula when selling an umbrella to our guests.
6. If you cover the rain, you must spread it to dry before putting it away.