Take an empty eggshell and coat it with wax (thin)
Draw a picture on it with something sharp (cut the wax)
Soak in vinegar for a few hours, and remove the wax.
The carved place was darkened by acetic acid.
Turned into a small production!
Nowadays, popular clothes hangers generally have no windproof function, and users often encounter such troubles: a newly washed dress hangs on a rope to dry, and when the wind blows, it falls to the ground and needs to be washed again. The self-locking windbreaker hook I invented can relieve everyone's troubles. The above picture is a schematic diagram of the self-locking windproof clothes hanger: in the above picture, (1) is a lock sleeve, (2) is a lock column, and a lever is formed by a rotating shaft (3) and a crank (4), and the lever rotates with (3) as a fulcrum under the action of a counterweight (5). When hanging clothes, just lift the crank (4) by hand or hook. Under the action of gravity, the lock sleeve (1) and the lock column (2) are automatically separated. The user can hang the clothes hook on the rope smoothly and then loosen the crank. Under the action of the counterweight (5), the lock post (2) is automatically connected with the lock sleeve (1). The process of taking out the clothes hanger is also very simple: just lift the crank (4) upward by hand or hook, the lock will automatically open, and the user can conveniently take off the clothes hanger. This self-locking windproof clothes rack can not only be hung on the rope by hand to dry clothes, but also the user does not need to climb up if he wants to dry clothes in a higher place. He can hang or take off his clothes easily just by holding the crank with the hook. At the same time, the clothes hanger also has the characteristics of simple manufacture, good reliability and low cost. My little invention won the national invention patent.
The lid of this carton is usually covered to prevent dirt and dust from entering. When you want to take the paper in the box, just lift the lid. With the lifting of the lid, the paper in the box will be lifted automatically, which is very convenient to pick up. After use, once the lid is closed, it will return to its original position. This kind of automatic paper box is most suitable for holding toilet paper. The size of the carton can be designed according to your own needs. Multimedia teaching resource library provided by China Education Star.
Labor-saving screwdriver
(Editor's Note: People's Education Edition Nature Book 1 1 Lesson 65438+Axis 06)
The child is small and weak, so it is very difficult to twist the screws with a screwdriver. Sometimes it takes a lot of effort to screw the screws. A clever boy came up with a good idea and made a labor-saving screwdriver.
Material: wooden handle screwdriver, small iron bar.
Tool: drill.
Production method:
1. Drill a small round hole on the wooden handle of the screwdriver.
2. Insert a small iron bar into the round hole.
When screwing the screw, one hand presses the screwdriver downward, and the other hand pulls the iron bar to make a circular motion.
Innovative invention and production method 1, homemade badminton
Preparation materials: an empty beverage bottle, two foam fruit nets, a rubber band and a glass ball.
Production process:
1. Take an empty 250ml beverage bottle and cut off the upper part of the bottle body;
2. Divide the cut part into 8 parts, cut it to the bottleneck with scissors, and then cut each part into a petal shape with the same size;
3. Cover the foam fruit net outside the bottle and fix it at the mouth of the bottle with a rubber band;
4. Wrap a glass marble with another foam fruit net and plug it into the bottle mouth until it is exposed about1cm;
5. Cut off half a table tennis ball, cover the bottom of the hemisphere on the bottle mouth, cut the four sides into whiskers, cover the bottle mouth and fix it with rubber bands.
6. After beautification, a homemade badminton is finished. Hit a dozen with a badminton racket and see how it works.
2, homemade soap paper
Production materials and tools:
White paper with good water absorption, small pieces of soap, writing brush and disposable beverage cans.
Production method:
Chop up the soap first, put it in a jar, put a proper amount of water in it, heat the cup on the stove, and when the soap melts, cut the white paper into the size of a matchbox, coat it with soap one by one, then take it out and dry it in the shade, and you can make soap paper.
3. homemade hot air balloon
1. First, we cut 6-8 leaflike pieces of paper from soft paper.
2. Fold them in half and stick the edges together to make a balloon.
3. Stick the four connecting wires to the bottom of the balloon with adhesive tape. Fix the other end of the line on the table with plasticine.
Try to set the speed of the hair dryer very slowly. Aim the air outlet upward at the opening at the bottom, and then turn on the switch. The balloon will gradually get bigger, tighten the line and leave the table.
4, homemade flashlight
The specific manufacturing method is: lift one end of an abandoned can (such as Lulu beverage can) and beat the other end with a round hammer. Roll up two 1 batteries with thick corrugated cardboard and put them in a can, with the positive pole facing up and the negative pole facing down. Find a suitable plastic cover (for example, the magic big roll cover can just be buckled on Lulu's beverage can), and dig a round hole in the center of the cover, the size of which is suitable for the light bulb to be inserted tightly. Insert the bulb base into the small hole. Take a section of tracing wire, peel off the wire skin at both ends, wrap one end around the lamp cap, and tie a small hole at the other end from the side of the plastic cover. Put the plastic cover on the jar. Check whether the bulb and battery are in close contact. Disposable flashlights will be ready here. When in use, press the wire on the side wall with your thumb on the unpainted weld away from the can, and the flashlight will glow. When your thumb jumps off the wire, the flashlight will go out, which is very convenient to use.
5, homemade solar cookers
Find a concave reflective bowl on a big flashlight, and cut it into a cylinder about 4 cm long with rigid foam plastic or wood, just enough in diameter to fit into the round hole of the reflective bowl. Drill a fine hole horizontally at one end of the cylinder, insert an iron wire with a diameter equivalent to the aperture, and then bend the two ends of the iron wire exposed outside the cylinder at 90 degrees, leaving 5 cm each. Insert the cylinder into the round hole of the reflective bowl, and then insert both ends of the iron wire on the foam plastic or wooden bottom plate. Sharpen both ends of a thin bamboo stick, insert one end into the cylinder in the center of the reflective bowl, and insert a small piece of potato at the other end. Put the device in the sun, let the reflective bowl face the sun, and then, patiently adjust the length of the bamboo stick so that the inserted potatoes are just in the focus of light. Before long, the potatoes will be cooked by the sun and smell delicious.
6, homemade colored candles
Materials: colored crayons, wax
Production method:
1. Find an abandoned canned beverage barrel (for example, 1.25 liter coke bottle), cut off the lid and cut the wax into the barrel.
2. Put the bucket in hot water, stir the wax inside and let it melt completely. It is best to use boiled water. But ask your parents for help, or do this step under their supervision.
3. Pour the molten liquid into a beautiful container (for example, put a heart-shaped chocolate box). Don't pour too much. As for the reason, look down. Of course, you have to put the thread as a candle core in the container first.
4. The initial idea of wax cooling, A, according to the method of surface painting, poured molten colored crayons into it (colored crayons come in handy at this time). In this way, different colors of wax are added layer by layer, and beautiful candles are made.
7. Self-made wall-mounted flower basket
Materials and tools: two sprite bottles, glue, meat cleaver, scissors.
Production method:
1. Remove the green bottom cover of Sprite bottle, cut it into lotus shape, turn it over and stick it on the bottle body to form the base.
2. Cut a 2 cm wide green ring from the green bottom sleeve and put it on the bottle.
3. Remove the bottleneck, and cut a wide band of 13cm long and 8cm wide and several narrow bands of 3cm wide on the bottle body.
4. Carve a pattern on a 3 cm narrow strip with a meat cleaver? As shown in figure 3, then fold these narrow strips outward and insert the green ring from bottom to top.
5. Take another beverage bottle, use the bottle body and cut out 6 leaves with scissors, the length is 17 cm.
6. Nail the flower basket on the wall, insert leaves and flowers, and the wall-hung flower basket will be ready.
8, homemade cockroach catching box
Take a piece of 220× 150(mm) cardboard.
The most important part of the capture box is the capture surface. Take a piece of plastic film, cut it into the same size as the bottom of the box, coat it with adhesive and spread it on the bottom of the box. Whether you can catch cockroaches depends on the adhesive. The adhesive has two functions: one is to introduce the cockroach into the box, and the other is to firmly stick the cockroach to the catching surface. Preparation of attractant: Mix 40% meat powder, 50% flour and 10% bean cake, with a total amount of about 20g, and mix well for later use. The adhesive is prepared by mixing 20g of rosin and10g of vegetable oil, heating to gel, and uniformly mixing attractant and adhesive.
Spread the prepared paste evenly on the grasping surface lined with plastic film, then fold it inward according to the original dotted line, and finally insert the tongue piece B into the notch A..
Because the mixture of rosin and vegetable oil is not dry, the viscosity of bait can be as long as one week. Put the trap box in the place where cockroaches haunt. Because the box is dark and has the bait that cockroaches like, cockroaches will climb into the box to fight for the bait and get stuck on it. When it is full, the carton can be crushed and discarded, and the plastic film can be removed and replaced with plastic film coated with bait, so that the box can be reused.
If the size of the catching box is enlarged and the composition of the adhesive is slightly adjusted, the paper mousetrap can be made by thickening the coating.
You can refer to it