A detailed explanation of Gao Xixin's driving test subject III in Sheng Da
First, the examination process of subject three (daily examination)
1. computer broadcast: get on the bus and prepare for the exam; Get on the bus and start the exam.
1) After hearing the password of "Get on the bus and start the exam", the examinee gets off with the onboard checker.
2) Bypass the car from the rear, and touch the four contact points of the car body with the inspector (every time the inspector touches the light). 3) Open the car door, get on the bus and close the door. Put the inspection instrument back in its original position.
2. Computer broadcast: simulate the night light to start the exam (immediately turn on the headlights to the low beam)
1) Pass the intersection ahead-alternate low beam to low beam 2) Overtake in front-alternate low beam to low beam 3) Temporary parking on the roadside-turn off headlights and turn on warning lights 4) The road ahead is well lit-turn on headlights to low beam and turn off warning lights 5) The road ahead is not lit-the low beam turns into high beam.
3. Computer broadcast: Start (turn off headlights)
1) fasten your seat belt, turn on the turn signal for more than 3S, and press the horn 2) to start (step on the clutch, shift to 1 gear, and release the brake).
3) When driving in the middle lane, change lanes, and the 2nd gear is placed directly behind the car body (1 gear cannot be used continuously for more than 40S).
4. Computer broadcast: change lanes to prepare for the exam and change lanes to open the exam.
1) Turn on the left turn signal for 3S and then shift to the left lane (look in the rearview mirror).
2) (Turn around with the left turn signal 3S-turning around here is not a starting project, and the computer will report the addition, subtraction and position reduction to prepare for the exam before turning around)
3) (After the front of the car is turned off, the car will accelerate to 20Km/h immediately after the front of the car is turned off)
5. Computer broadcast: Add and subtract gears to start the exam.
1) The second gear speed is 20Km/h, and the third gear is engaged; -2nd gear12-27km/h 2) 3rd gear is accelerated to 35Km/h, and shifted to 4th gear; —— 3rd gear17 —— 37km/h 3) 4th gear is increased to 40Km/h, and 5th gear is engaged; —— 4th gear, 25-47km/h
4) Downshift is the same as above, and it is reduced to second gear (pay attention to the speed and engine speed when downshifting, and the engine speed should not exceed 2500r/min, and the shift of 2000r/min is relatively stable at the corresponding speed).
6. Computer broadcast: overtaking preparation test; Overtake and start the exam.
1) Turn on the left turn signal for 3S and then change lanes. After driving for a certain distance, return to the original lane.
2) (Go straight for a certain distance, then turn left, and turn left ahead)
7. Computer broadcast: turn left in front to prepare for the exam; Turn left ahead and start the exam.
1) Brake until the speed drops; Look around (keep the speed within 20Km/h) 2) Turn left for 3S and then turn.
8. Computer broadcast: Go straight and get ready to go; Go straight ahead and start the exam.
1) Drive in a straight line in 2nd gear and 3rd gear (you can drive in the inner lane or the outer lane according to the situation).
9. Computer broadcasting: prepare to start crossing the intersection; Start the exam through the intersection (with traffic lights)
1) Brake until the speed drops; Look around (keep the speed within 20Km/h) 2) (change the inner lane to the outer lane in advance and stop at the red light).
10. computer broadcast: turn around ahead and get ready to go; Turn forward and start the exam.
1) shift from gear 2 to gear1;
2) Turn right for 3S and drive on the right; (Wait for 3S and then press the solid white line on the right) 3) Turn on the left turn signal 3S and start to turn around; (Turn at the front of the car after passing the marked street lamp) 4) After the car body is straightened, shift to the second gear (1 gear cannot exceed 40S).
1 1. Computer broadcast: prepare for the exam through the crosswalk; Start the exam through the crosswalk (traffic light)
1) Brake until the speed drops; Look around (keep the speed within 20km/h and stop at the red light).
12. Computer broadcasting: preparing for the exam; Meet the bus and start the exam.
1) Don't move during the day and keep walking (don't move at night).
2) (Vehicles in the fast lane change lanes to the right lane when approaching the school district sign)
13. computer broadcasting: ready to start through the school area; Start the exam through the school area.
1) Brake until the speed drops; Look around (keep the speed within 20km/h)
14. computer broadcast: turn right at the intersection and get ready to go; Turn right at the intersection and start the exam.
1) Brake until the speed drops; Look around (keep the speed within 20Km/h, make a big turn and don't press the line).
15. computer broadcast: prepare to leave through the public relations bus station; Start the exam through the public relations bus station
1) Brake until the speed drops; Look around (keep the speed within 20km/h)
16. computer broadcast: pull over and get ready to go; Pull over and start the exam.
1) (you can stop and wait for the parking space before you report the departure)
2) Shift 1, turn on the right turn signal 3S and drive to the right. It is best to let the wheel press just half of the white line (no pressure or no pressure outside).
3) Park the car in the whiteboard induction area, step on the brake, hold the handbrake and put it in neutral. 4) open and close the door (the computer will report "passed the exam"; "Fail the exam")
Second, subject three exam process (night exam-night exam)
The night test is basically the same as the day test, and the differences are as follows: computer broadcast: the night test begins-turn on the headlights and turn on the low beam; Computer broadcast: overtaking begins to test-alternating low beam and far beam.
Computer broadcast: turn around in front and start the test-the low beam becomes the high beam, and then change back to the low beam after adjusting the head. Computer broadcast: start the test through the crosswalk-turn on the warning light and turn off the headlights after the low beam stops.
Remarks: The computer is not equipped with far and near light conversion monitoring for the subject of meeting cars.