Draw a line at the correct position to be drilled in advance, and install a drill bit with the same diameter as that to be drilled. Connect the water pipe to the machine, and then turn on the power. Generally, drilling holes are held by arms and can be pushed slowly. The service life of an electric drill depends on the quality and what you drill. Generally, concrete meets too many steel bars around 20 meshes, which is 10 mesh.
When in use, first measure the center position of the hole to the position of the strip groove in the center of the drilling rig base, then punch a hole in the wall with an impact drill, bury the expansion fixing bolt, fix the drilling rig on the wall, and then connect the water pipe with even force. The four bolts of the base can adjust the angle. If the wall is not strong enough, it must be fixed with through-wall bolts after opening the wall.
Question 2: How to drill a diamond is to aim the drill at the position to be drilled, press the switch button, the drill will rotate, and then you can drill.
Question 3: How to punch holes in air conditioners? Is it perforated with diamonds? Usually, this hole is made of diamonds, but if you are afraid of polluting the wall, you can also dig it with an ordinary drill, but the efficiency is relatively low. It's best to punch holes with diamonds. I hope it helps you!
Question 4: How to drill a hole with a fixed diamond, draw a line where drilling is needed in advance, and install a drill with the same diameter. Connect the water pipe to the machine, and then turn on the machine when the amount of water is suitable. Usually drill holes with your arms and push them forward slowly.
A diamond drill is actually a diamond drilling machine. Because this machine can drill holes with water, it is commonly called diamond drill. When drilling a diamond bit, water is used to bring out powder, and cooling the bit plays a role in lubrication. At present, there are two kinds of hot drilling commonly used: desktop hot drilling and hand-held hot drilling. Desktop rhinestones can be fixed on the wall because of their high power. Generally, they can be drilled into 200mm round holes. However, desktop rhinestones are too bulky and inconvenient to carry, and generally only professional rhinestone drillers use them. Hand-operated (also known as gun type) is generally used to install air conditioners.
Question 5: What is a diamond punch? Is to use high pressure to make water flow through tiny cracks. Due to the extremely high speed and kinetic energy of tiny water flow, it is easy to punch holes in steel plates or cut other hard objects such as steel.
Question 6: What should I do if the drill bit of the diamond drill gets stuck? Remove the drill bit with a big wrench, and then slowly turn it in the opposite direction with a wrench. If it can't turn, you can tap the drill bit gently with a small hammer. Be careful not to knock too hard. If you push too hard, it's easy to bump the drill bit and it won't be used next time.
Question 7: What do you need to punch holes with table diamonds? Hammer, electric hammer, water pump, water pipe and diamond wrench with implosion screw gasket 16 should be relatively complete. If drilling holes regularly, you can also buy an automatic control device. One person can operate 3-4 sets of diamond automatic drilling control system devices. The patented products developed by Beijing Sifang Surprise Technology Co., Ltd. are affordable.
Question 8: Drilling skills of diamonds. Hehe, most people can't answer this question. First, you should hold the diamond firmly against the wall. When striking, the drill bit of the diamond can't be completely tangent to the wall, and it is easy to escape. The correct way is to let the bit tilt down about 50 degrees. After the drill bit drills a part of the wall, drill it deeper and then adjust it slowly. After the bit is adjusted, don't shake it, it is easy to burn. The broken motor occasionally shakes twice, which makes the gap between the drill bit and the wall bigger and easier to take out. Another problem is that in the process of hitting the ball, there should be neither too much nor too little water. You can adjust yourself if you hit it.
Question 9: If there is no running water, how to punch holes with a diamond? You can use the high water to supply water by yourself.
Question 10: To tell the truth, there is no good way to prevent the diamond from drilling, because the diamond definitely needs water, so it is inevitable that the water will flow to the wall. I think you should install air conditioning, so you can't dry the dirty wall with toilet paper. Of course, it would be much easier if there was still paint. Just touch up the paint.