Abstract: Screen windows can help us all have a good mosquito control product in the summer. Many people have installed and used them in their homes. If you want to buy screen windows, reasonable installation is very important. , to ensure that our screen windows have the best use effect. The following will tell you how to install and disassemble the screen windows and what to pay attention to. I hope it can help you. 1. Screen window installation method
1. Assemble the square frame
Put the gauze box at the top, place the two air troughs on the left and right sides under the gauze box, and place the bottom at the end. Below, form a square frame. Then use six screws, two screws are placed in the contact place between the yarn box and the two air ducts, four screws are placed in the contact place between the two air troughs and the bottom pad, two screws are placed on each side, and the two screws are placed one On the underside, one on the side. After fixing the square frame with these six screws, you can proceed to the next step.
2. Select the location of the screen window
Then you can place the screen window where it needs to be installed. It should be noted that the gauze box should be vertical; the two air ducts should be placed in the middle, and the distance from both sides of the window frame should be the same to achieve left-right symmetry; the bottom should not be placed directly on the window frame, but should be placed low About 5 cm below the frame of the window. After these key points have been determined, simply fix them with clips.
3. Drill holes and install screws to fix the invisible screen window
Next, use an electric drill to drill holes on the inside of the leather strip of the window frame, at the two air ducts and the bottom. When using an electric drill, a 3.2mm drill bit is most suitable. The number of holes to be drilled depends on your needs, 6-14 holes are enough. Finally, install the matching screws at the hole location, and the screen window is installed.
2. Precautions for screen window installation
1. First, accurately measure the size of the required installation position of the window, and place the two aluminum large holes directly opposite the small holes. According to the measured Cut the aluminum and cover to size. Drill 8-10mm holes in the aluminum material according to the installation location (the size of the hole is the diameter of the selected expansion bolt). Determine the installation location of the alarm or transmitter, drill a 6mm hole in the upper corner of the window frame, introduce one end of the wire rope into the room and leave sufficient length. Place the aluminum material at the desired installation position on the wall, drill 8-10mm holes in the wall with an electric hammer, and fix it to the wall with expansion bolts; tighten the wire rope in sections, be careful not to use too much force, and tighten continuously for 3 to 4 times until the wire rope reaches the required tightness.
2. Clamp the wire rope between the first fastening pads and tighten. The wire rope is always knitted up and down around a set of fastening screws with a small distance. Cover plate: Buckle the cover plate and rivet it tightly with rivets (note: do not use too much force when tightening the rivets to prevent the cover plate from deforming), and use diagonal pliers to cut off the rivet core. Determine the number of transverse steel wires according to the height of the window (generally pull a transverse steel wire at 150cm). Determine the position of the transverse steel wire and pull a standard line to ensure that the cross buckle is a straight horizontal line. Pull the wire rope to the clip position and lock it with the cross buckle. Finally, introduce the steel wire rope into the room, peel it off to expose the two ends of the inner core, and connect them to the two wires of the alarm or transmitter, and fix it on the wall.
3. How to disassemble the screen window
1. First, you need to carefully remove the sealing strip that fixes and seals the screen window. You must be careful when operating, because excessive force will often cause the screen window to open. The original intact plastic screen window is damaged. If the sealing strip is fixed tightly, it is also recommended to use a screwdriver to carefully pry it open from the bottom of the seal. The sealing strip is relatively cheap, so even if it is damaged, the integrity of the plastic steel screen window must be ensured.
2. After removing the sealing strip, lift the entire screen window up to the top of the slide rail, and then remove the entire window sash. After taking it off, the screen window may be slightly deformed due to external force. This is normal and it is not recommended to adjust it by yourself. If you follow it again, you will need a professional to adjust it.
How to remove the plastic screen window
3. After removing the screen window, you can remove the corresponding glass of the screen window. It is recommended to use a flat-blade screwdriver of moderate width to slowly pry it open. When there is a gap in the glass, do not use too much force. When the glass is slightly pried open, change the force. It is recommended to apply force diagonally so that the glass can be removed. Remember to take preservation measures after removing the glass to prevent the glass from breaking or injuring anyone.