How to use the electric toothbrush
Introduction: The electric toothbrush is a new type of daily necessities introduced in recent years. Usually, when we clean our teeth, we usually use an ordinary toothbrush to clean them. Maybe you think that your teeth have been cleaned after you brush them, but this is not the case. The dental plaque bacteria on your teeth may not be clean. Investigation shows that using electric toothbrush to clean teeth has a higher degree of cleanliness, which can remove dental plaque bacteria from teeth more thoroughly and reduce gum bleeding at the same time. Do you know how to use the electric toothbrush? Next, let me give you a detailed introduction of how to use the electric toothbrush.
classification of electric toothbrushes
In principle, electric toothbrushes can be divided into two types: rotating and vibrating. The rotating electric toothbrush uses a motor to drive the circular brush head to rotate, which can enhance the friction effect when brushing teeth, and the cleaning effect of the rotating electric toothbrush is much higher than that of the toothbrush we usually use. The vibrating electric toothbrush is an electrically driven vibrating motor installed in the toothbrush, which can make the brush head swing at high frequency perpendicular to the brush handle. Although its swing amplitude is relatively small, it can achieve efficient brushing effect when used, and the cleaning effect of the vibrating electric toothbrush is better than that of the rotating electric toothbrush.
According to the classification, electric toothbrushes can be divided into the following categories:
Electric toothbrush: This kind of toothbrush uses a high-speed motor to make the brush head rotate and vibrate at high speed to achieve efficient cleaning effect.
sonic toothbrush: this kind of toothbrush is actually a toothbrush that cleans teeth by vibration, but it mainly uses the frequency similar to sonic vibration to make the bristles move quickly to achieve the effect of cleaning teeth.
ultrasonic toothbrush: ultrasonic toothbrush mainly uses ultrasonic ability to clean up germs and impurities around teeth, and its cleaning range can cover all parts of Asia. Ultrasonic energy can be transmitted to teeth and gum surfaces through bristles, which can loosen the adhesion between dental plaque, tartar and teeth, and at the same time destroy the parasitic reproduction of bacteria hidden between gums and tooth surfaces. Ultrasonic can also act on cell membranes, accelerate blood circulation, promote the renewal of metabolism and prevent gum bleeding.
How to use the electric toothbrush
The use of the electric toothbrush is actually very simple. In order to help you use the electric toothbrush better and ensure the good cleaning effect of the electric toothbrush, I will introduce how to use the electric toothbrush in detail for you here.
1. Before using the electric toothbrush, the brush head of the electric toothbrush should be put into the toothbrush shaft until the brush head and the toothbrush shaft are buckled.
2. After installing the brush head, it is necessary to adjust the softness of the bristles. The softness of the bristles is related to the water temperature. Soaking the bristles in warm water is softer, while cold water is moderate, and ice water is slightly harder. When you use an electric toothbrush for the first time, you should soak it in warm water before using it. The toothbrush bristles soaked in warm water are very soft and comfortable. After soaking the bristles in warm water for many times, you can decide the hardness of the bristles yourself.
3. When squeezing toothpaste, in order to prevent the toothpaste from splashing, it is best to squeeze the toothpaste on the toothbrush before turning on the power of the electric toothbrush, and when squeezing toothpaste, squeeze the toothpaste vertically into the gap in the bristles and squeeze a proper amount of toothpaste.
4. How to brush your teeth effectively? Everyone should pay attention to it when brushing your teeth. Put the brush head into the thinnest front teeth and let the teeth move moderately between the bristles. When the toothpaste bubbles, turn on the electric switch of the toothbrush. After the brush head of the toothbrush starts to vibrate, move the toothbrush from the front teeth to the back teeth with moderate force. Usually, it takes only two minutes to brush your teeth with an electric toothbrush, which can completely clean the teeth.
5. Under normal circumstances, there is also a tongue scraper on the back of the brush head of the electric toothbrush. After cleaning the teeth, the tongue coating on the tongue can be completely cleaned by using the tongue scraper.
6. After using the electric toothbrush, if you don't want the foam of toothpaste to splash everywhere, it's best to turn off the power of the toothbrush when you take it out of your mouth.
7. How to use the electric toothbrush? The last cleaning step of the electric toothbrush is: after using the toothbrush, put the brush head of the toothbrush in water, turn on its electric switch, gently shake it a few times, and then knock on the brush head, so as to clean the foreign matter and toothpaste left on the bristles.
notes on the use of electric toothbrush
above, I have introduced how to use the electric toothbrush for everyone. Finally, I have summarized some notes on the use of the electric toothbrush for everyone. Let's take a look at it now.
1. When choosing an electric toothbrush for the elderly and children, it is best to choose a toothbrush with an integrated brush head and handle, which can prevent the problem of swallowing the brush head by mistake.
2. When choosing an electric toothbrush, it is best to choose a small brush head, so as to go deep into the mouth and clean the teeth inside.
3. Compared with the ordinary toothbrush, the brush head of the electric toothbrush can move at the speed of thousands or even tens of thousands times per minute under the drive of electric power, and its brushing efficiency is much higher than that of the ordinary toothbrush. However, during use, we should also prevent the gum from being damaged by excessive force.
4. When using the electric toothbrush, you should ensure that you have at least 2 minutes to brush your teeth, and at the same time make sure that the inside and outside of each row of teeth are clean, especially the lower teeth, and you must consciously clean them.
5. The brush head of the electric toothbrush should be cleaned regularly. After long-term use, the bristles of the brush head will become rough, which is easy to damage the gums. Therefore, the brush head must be replaced in time after 3 months of use.
how to use the electric toothbrush?
When using an electric toothbrush, you need to hold the toothbrush firmly and move the brush head slowly against your teeth. As for where to brush first, just follow your personal habits.
when brushing teeth, insert the brush head through the thinnest front teeth. Let the teeth be sandwiched between the three bristles and pulled back and forth with moderate force. When the toothpaste bubbles, turn on the electric switch. After the brush head vibrates with moderate force, move the toothbrush back and forth from the front teeth to clean all the teeth. Generally speaking, it takes only two minutes to brush your teeth with a three-sided electric toothbrush.
Precautions:
1. The electric toothbrush should not be placed at high temperature or exposed to the sun for a long time, because the bristles are easily deformed at high temperature.
2. Wash the toothbrush thoroughly after each use, and throw off the water as much as possible. Then put the toothbrush in a ventilated and sunny place to dry and sterilize it.
3. If conditions permit, you can buy two or three toothbrushes at the same time and use them alternately, so as to prolong the drying time of toothbrushes. This is especially important for people with gingivitis and periodontitis. The elasticity of the toothbrush can also be ensured when it is used in turn.
4. If the bristles are scattered or curled, they must be replaced in time, otherwise it will be bad for teeth and gums.
how to use the electric toothbrush?
Correct use of electric toothbrush:
1. Install the brush head correctly: When installing the brush head, make sure that the brush head is tightly inserted into the toothbrush shaft to avoid the loosening of the brush head handle.
2. Before using the electric toothbrush, pay attention to soak the brush head with warm water to adjust the softness of the bristles. If the brush is directly opened with cold water, the bristles are hard and the vibration frequency can't adapt, so gum bleeding occurs. If your teeth are sensitive, you'd better use soft bristles.
3. Toothpaste is squeezed into the bristles. In the process of squeezing toothpaste, in order to avoid toothpaste splashing around, it is best to align toothpaste vertically with the middle seam of bristles and squeeze a proper amount of toothpaste.
4. Although you don't need to think too much about brushing skills when using electric toothbrush, how to brush your teeth effectively to make your teeth cleaner is also a problem that needs attention. When brushing your teeth, put the brush head close to the thinnest front teeth and pull it back and forth, being careful not to use too much force. After the toothpaste bubbles, turn on the electric switch. After the brush head vibrates, use moderate force to move the toothbrush back and forth from the front teeth. Brush for about 3 seconds at each interval, and all teeth can be cleaned in two minutes.
5. If you buy an electric toothbrush with a tongue scraper, you should make good use of it. After brushing your teeth, use the tongue scraping edge on the back of the brush head to scrape off the tongue coating, which can achieve the effect of thoroughly cleaning your tongue and make your mouth healthier and cleaner.
6. The cleaning of electric toothbrush is much more convenient and hygienic than that of ordinary manual toothbrush. After brushing teeth, put the brush head into water, turn on the electric switch, gently shake it a few times, and then tap the brush head to remove the foreign matter and toothpaste left on the bristles.
there are two ways to hold an electric toothbrush: the hand-held method and the pen-held method. The hand grasping method can make the toothbrush fit closely with the palm of your hand, and the pen grasping method can operate the teeth carefully with relatively light force.
Simple steps:
1. Tilt the toothbrush slightly, make an angle of 45 degrees with the gums of the teeth, and brush the occlusal surface of the teeth vertically;
2. Brush the back of the molars with the front end of the toothbrush.
how to use the electric toothbrush
1. soak the brush head of the electric toothbrush in warm water for half an hour before using it for the first time.
2. Put the brush head tightly into the toothbrush shaft and check it several times.
3. finally, squeeze the toothpaste on the brush head, put the toothbrush in your mouth and brush it back and forth.
Extended information:
When using the electric toothbrush, you should pay attention to the following details:
1. Do not put the electric toothbrush at high temperature or expose it to the sun for a long time, so as to avoid the bristles from being deformed and bent due to high temperature;
2. Wash the toothbrush thoroughly after each use, and throw off the water as much as possible. Put the toothbrush head up in a mouthwash cup, or put it in a ventilated and sunny place to make it dry and sterilize;
3. If conditions permit, you can buy two or three toothbrushes at the same time and use them alternately, so as to prolong the drying time of toothbrushes. This is especially important for people with gingivitis and periodontitis. In addition, rotation can also maintain the elasticity of toothbrush bristles;
4. Old toothbrushes whose bristles are scattered or curled and lose elasticity must be replaced in time, otherwise it will be bad for teeth and gums;
5. The toothbrush should be thoroughly cleaned and disinfected once a week;
6. Toothbrushes should not be shared, in case of mutual infection.
correct use of electric toothbrush
correct use of electric toothbrush
correct use of electric toothbrush, the structure of electric toothbrush is obviously different from that of ordinary toothbrush, and in terms of cleaning principle, electric toothbrush relies on the flowing cleaning force caused by high-frequency vibration of motor to thoroughly clean the oral cavity. The following is the correct use of electric toothbrush.
correct use of electric toothbrush 1
1. Install the brush head: tightly sleeve the brush head into the toothbrush shaft until the brush head engages with the metal shaft.
2. Soak in warm water: adjust the softness of bristles with warm water: warm water: soft; Cold water: moderate; Ice water: slightly hard. It is strongly recommended that first-time users soak in warm water before using! Because more than 95% people in China suffer from periodontal disease, they will feel more sensitive in the gums, and the bristles soaked in warm water are very soft and comfortable to brush. After using them for 2~5 times, the hardness of the bristles will be determined according to your preferences.
3. Squeeze toothpaste: align the toothpaste vertically with the middle seam of the bristles and squeeze a proper amount of toothpaste. In order to avoid toothpaste splashing, it is best to squeeze toothpaste before turning on the power.
4. Brush your teeth effectively: When brushing your teeth, insert the brush head through the thinnest front teeth. Let the teeth be sandwiched between the three bristles and pulled back and forth with moderate force. When the toothpaste bubbles, turn on the electric switch. After the brush head vibrates with moderate force, move the toothbrush back and forth from the front teeth to the rear teeth to clean all the teeth! Generally speaking, brushing teeth with a three-sided electric toothbrush takes only two minutes at a time to completely clean.
5. Use a tongue scraper: After brushing your teeth, it is best to scrape off the tongue coating with the tongue scraping edge on the back of the brush head to achieve the effect of thoroughly cleaning your tongue.
6. Foam splashing: Please turn off the toothbrush before taking it out of your mouth.
7. Cleaning toothbrush bristles: After each brushing, put the brush head into water, turn on the electric switch, gently shake it a few times, and then tap the brush head to clean the foreign matter and toothpaste left on the bristles.
correct use of electric toothbrush 2
1. When using the electric toothbrush for the first time, the brush head of the electric toothbrush should be installed correctly. During the installation process, it must be confirmed that the brush head is tightly inserted into the toothbrush shaft to avoid the injury caused by the loosening of the brush head handle during use.
2. Before brushing your teeth, you can soak the brush head in warm water to adjust the softness of the bristles, and then squeeze in a proper amount of toothpaste. Remember to apply the toothpaste evenly to your teeth first, put the brush head in your mouth and then start the toothbrush, otherwise it will cause the toothpaste to splash.
3. At present, electric toothbrushes are generally equipped with a variety of cleaning modes. If it is the first time to use electric toothbrushes, it is recommended to choose a softer resistance mode to adapt gradually. After adapting for a period of time, you can choose a suitable cleaning mode according to your own oral and dental conditions.
4. In the use process, you only need to hold the electric toothbrush and move your arm back and forth, and you don't need to use too much force. It is suggested that the bristles and gums move slowly along the gums at an angle of 45, and each area of the oral cavity can be cleaned in turn according to the tips of the electric toothbrush. After cleaning the toothbrush, turn off the electric toothbrush first, and then take it out of your mouth.
5. After using the electric toothbrush, it is recommended to rinse the toothbrush head with clean water, then wipe the body with a dry cloth to keep it dry, and then place the electric toothbrush in a ventilated and cool place, so as to avoid damage to the electric toothbrush caused by moisture or moisture environment and effectively prolong the service life of the electric toothbrush.
6. It is also very important to replace the brush head regularly, because the brush head of the electric toothbrush will gradually suffer from greater wear after long-term use, which will affect the cleaning ability of the electric toothbrush. Moreover, if the electric toothbrush is placed in a humid place for a long time, it is easy to cause bacteria to grow on the brush head, so it is necessary to replace the brush head in time.
the correct way to use the electric toothbrush 3
You must hold your hand firmly, and adopt the gesture of holding the pen like an ordinary toothbrush.
From the place slightly away from the teeth, slowly close to the surface of the teeth, and brush one part for about 3-7 seconds.
moving method: move the toothbrush slowly, one part at a time. Don't brush by hand, but let the electric toothbrush vibrate. Where there is a lot of tartar, brush it for more time.
after using it, wash it with running water when the machine starts to vibrate, and then dry it fully. Do not boil it for disinfection.
if the bristles are open, the efficiency of tooth brushing and tartar removal will be reduced. At this time, it is necessary to replace the brush head, and the replacement interval is usually three to four months.
to remove dental plaque, dental floss and interdental brush should be used together.
Where do you brush your toothbrush?
In addition to keeping your teeth white, the most important thing is to remove dental plaque, which is a bacterial biofilm. If it is not removed in time, it will easily lead to oral diseases such as tooth decay, gingivitis and periodontitis. At present, the most recognized Pap brushing method by dentists is to make the bristles vibrate rapidly in the gingival sulcus to remove dental plaque. For the electric toothbrush, the tremor will automatically proceed, and we have to do it.