SAE AS1072E Fire Rated Sleeving: Aerospace - Marine High Temperature, Heat Resistant, Flame Retardant, High Temperature Resistant Silicone Rubber Coated Fiberglass Sleeving and Jacketing: Protects Critical Hydraulic, Oil and Fuel Lines Cross Reference Table (allowing qualified hose assemblies to pass AS1055D testing) 500°F/260°C Continuous Exposure: Higher Intermittent FlameShield? Aviation/Aerospace Grade High Temperature, Heat Resistant, Flame Resistant and Fire Resistant Sleeve Jacket per SAE AS1072E Standard Manufactured to meet the fire test standards of AS1055D; and the requirements of FAA TSO?-?C53a and TSO?-?C75. It can be used on all fuel, oil, hydraulic, fire extinguisher and prop feather lines. FAA-specified "fire-resistant" hose must withstand direct flame for 15 minutes under specified flow conditions without failure. Under these conditions, the firebreak must withstand 5 minutes of exposure. Fire-rated hose lines are obtained when the appropriate size of fire-rated casing is selected and assembled correctly using the appropriate clamps. Fireproof casing sizes range from 0.25" ID to 5" ID. 25 steps. Aerospace/Aerospace/Marine Fire Sleeves
On all of these products (fire sleeves), the molten metal simply slides off an extra heavy-duty coating of high-temperature silicone rubber to provide excellent burnthrough protection.
Fire Rated Sleeves Fire Rated Sleeves and Jackets withstand melt spatter and welding spatter. Withstands continuous exposures to 500°F/260°C; 2200°F/1205°C for up to 15 minutes, short flash offset to 3000°F/1650°C. Xi'an Fuchuan Electronics About SAE-AS1072? Aerospace Fireproof Sleeve Substrate Technical Specifications Fiber Type: E Glass
Specific Gravity: 2.54-2.69
Breaking Toughness: 1.71 gf/TEX. standard. 1.71 gf/TEX Wet
Effects of Heat: Will not burn; maintains 75% tensile strength at 343°C/649°F;
at 732-877°C / 1349-1610°F - Softens; melting point 1121-1182°C / 2049-2159°F
Tensile Strength: 450,000-500,000 psi.
Acid and alkali effects; acid resistance is fair. Good resistance to most alkalis.
Elongation at break: 4.81% standard.
4.81% wet
Elastic recovery: 100%
Effect of bleach and solvents: not affected
Average stiffness: 2824.3 cn/TEX
Silicone Rubber Technical Specifications
Durometer, Shore A: Initial; 35 years, 240 hours @ 200°C; 45
Tensile Strength (psi): Initial ; 875 years, 200°C, age 240 hours; 800
Elongation %: Initial; 500 years, 200°C, age 240 hours; 200
Flammability, UL94 ; V-1
Dielectric Strength (Volts/mil); 485
Coating Thickness
AS1072 Specifications: Minimum: .03" (0.8mm )
Nominal average measured at 10 locations over 12" length: .05"
Fluid Resistance
Phosphate Ester Hydraulic Fluid
MIL-H-5606 hydraulic oil
MIL-T-5624 jet fuel
MIL-L-6082 lubricating oil
MIL-L-7808 lubrication Oil
MIL-L-23699 Lubricating Oil
MIL-H-83282 Hydraulic Oil
Other models: SAE AS1072-04-SIL-FG, 1/ 4" I.D.SAE AS1072-05-SIL-FG, 5/16" I.D.SAE AS1072-06-SIL-FG, 3/8" I.D.
SAE AS1072-07-SIL-FG, 7/16 " I.D.
SAE AS1072-08-SIL-FG, 1/2" I.D.
SAE AS1072-09-SIL-FG, 9/16" I.D.
SAE AS1072-10-SIL-FG, 5/8" I.D.
SAE AS1072-11-SIL-FG, 11/16" I.D.
SAE AS1072-12-SIL- FG, 3/4" I.D.
SAE AS1072-13-SIL-FG, 13/16" I.D.
SAE AS1072-14-SIL-FG, 7/8" I.D.
SAE AS1072-16-SIL-FG, 1" I.D.
SAE AS1072-18-SIL-FG, 1 1/8" I.D.
SAE AS1072- 20-SIL-FG, 1 1/4" I.D.
SAE AS1072-22-SIL-FG, 1 3/8" I.D.
SAE AS1072-24-SIL-FG, 1 1/2" I.D.
SAE AS1072-26-SIL-FG, 1 5/8" I.D.
SAE AS1072-28-SIL-FG, 1 3/4" I.D.
SAE AS1072-30-SIL-FG, 1 7/8" I.D.
SAE AS1072-32-SIL-FG, 2" I.D.
SAE AS1072 -36-SIL-FG, 2 1/4" I.D.
SAE AS1072-38-SIL-FG, 2 3/8" I.D.
SAE AS1072-40-SIL-FG , 2 1/2" I.D.
SAE AS1072-42-SIL-FG, 2 5/8" I.
D.
SAE AS1072-44-SIL-FG, 2 3/4" I.D.
SAE AS1072-46-SIL-FG, 2 7/8" I.D.
SAE AS1072-48-SIL-FG, 3" I.D.
SAE AS1072-52-SIL-FG, 3 1/4" I.D.
SAE AS1072-56-SIL -FG, 3 1/2" I.D.
SAE AS1072-60-SIL-FG, 3 3/4" I.D.
SAE AS1072-64-SIL-FG, 4" I.D.
SAE AS1072-72-SIL-FG, 4 1/2" I.D.
SAE AS1072-80-SIL-FG, 5" I.D.
SAE AS1072 -96-SIL-FG, 6" I.D.