A metal pipe cutting machine 2 inches below the metal pipe cutting machine
Metal pipe cutting machine under 2 inches
Metal pipe cutting machine ECG2, which is less than 2 inches, is a professional cold cutting tool for cutting cast iron, carbon steel and stainless steel pipes produced by E-WORK. This machine adopts spring guide frame, so that the four blades walk in a line and the incision is straight. The thin and sharp blade is made of high-strength tool steel, which saves labor and cuts quickly. It is a pipeline cold cutting tool with high cutting speed on the market at present. Because the blade is sharp and cutting is more labor-saving, the handle of the pipe cutter can be designed to be shorter, which is very suitable for operation in a narrow space.
Operating steps:
1. Check the blade to ensure that the blade is suitable for the type of pipe to be cut.
2. Place the pipe cutter vertically on the pipeline, and the four contacts of the two elastic positioning claws should be evenly contacted on the surface of the pipeline. Tighten the handle so that the blade contacts the pipeline vertically, and the cutting depth can be less than 0.5mm..
3. After the pipe cutter rotates slightly, make sure that the cutting track is on the circumference (otherwise, loosen and reposition).
4. Swing the operating handle of the pipe cutter back and forth between 90 and140, and constantly tighten the operating handle for feeding (as long as the pipe cutter can rotate, the tighter the handle, the better).
5. Swing the handle back and forth and feed continuously until the pipeline is cut off.
Note: When cutting pipes, adding lubricating oil at the knife edge can not only save labor, but also prolong the life of blades and equipment.
Rotary pipe cutter
Rotary pipe cutter
Rotary pipe cutter series products are a series of professional cold cutting tools produced by E-WORK for cutting large-diameter carbon steel, stainless steel, cast iron and ductile iron pipes. Ultra-reasonable fuselage design and ingenious structural setting make pipe cutting faster and more labor-saving! The cutting blade is made of high strength tool steel. After special heat treatment, the strength and toughness of the blade are balanced, which not only ensures the rapid cutting of the blade, but also ensures the long-term wear resistance.
Operating steps:
1. Check the blade to ensure that the blade is suitable for the type of pipe to be cut.
2. Ensure that the rod end connected by bolts is in a proper position, which is suitable for the size of the pipeline to be cut. Loosen the turnbuckle evenly until the distance between the center of the rod end eye and one end of the turnbuckle is about 57 mm (2 1/4 inch). Open the release pin and connect the pipe cutter to the pipe to be cut. (If the clearance around the pipe is very small, you may need to untie 2 pins. Connect the release pin in place through the yoke part and the rod end, and place the spring-loaded guide part of the pipe cutter above the pipe. Tighten the two turnbuckles evenly by hand until all four cutting wheels touch the pipe. Tighten the turnbuckle every time the pipe cutter rotates 1/2 times. You can also use the turnbuckle to push the pipe cutter around the pipe.
3. While pushing the pipe cutter around the pipeline, tighten the turnbuckle as much as possible. (If sufficient tension is provided, the handle lever can be easily tightened by 0/2 turn of -65438+ turnbuckle.)
Articulated pipe cutter
Articulated pipe cutter
Articulated pipe cutter series products are a series of professional cold cutting tools produced by E-WORK for cutting carbon steel, stainless steel, cast iron and ductile iron pipes. Ultra-light body design and reasonable structural setting make the cutting performance more superior. The cutting blade is made of high strength tool steel. After special heat treatment, the strength and toughness of the blade are balanced, which not only ensures the rapid cutting of the blade, but also ensures the long-term wear resistance.
Operating steps:
1. Check the blades to make sure they are suitable for the type of pipe to be cut.
2. Rotate the operating handle of the pipe cutter repeatedly to make the rod end of the feed screw rise to a proper position to adapt to the pipe diameter to be cut.
3. Open the self-locking claw of the pipe cutter, open the lower support tool holder, and clamp the pipe cutter on the pipeline to be cut; Lock the self-locking claw, and then adjust the relative position between the cutter and the pipeline, so that the four top ends of the cutter guide rail contact with the surface of the pipeline at the same time, and ensure that the blade of the cutter is perpendicular to the pipeline to be cut.
4. Turn the operating handle of the pipe cutter slowly to see if the cutting track is on the circumference (otherwise, loosen and reposition).
5. Swing the operating handle of the pipe cutter back and forth between 90 and110, and tighten the operating handle continuously for feeding (as long as the pipe cutter can rotate, the tighter the handle, the better).
6. Swing back and forth and feed continuously until the pipeline is cut off.
Note: When cutting pipes, adding lubricating oil at the knife edge can not only save labor, but also prolong the life of blades and equipment.
Pipe climbing and pipe cutting beveling machine
Pipe climbing and pipe cutting beveling machine
Pipe climbing and pipe cutting beveling machine equipment is a pipeline processing equipment independently developed by E-WORK according to the market and prospect of pipeline service industry and combined with the technical force of our company. This product is light, accurate, efficient, modular design, fully considering the needs of users, and is an ideal choice for all kinds of pipeline cutting and beveling. The pipe climbing pipe cutting beveling machine is an automatic equipment which takes hydraulic pressure as the power source, uses the cutting principle of disc milling cutter and is driven by hydraulic pressure to cut and bevel. Firstly, the cut pipe is fed slowly through the threaded screw, and then the remote control cutting robot crawls along the circumference of the pipe to complete the cutting and beveling of the whole process pipe. The outside diameter can be machined from 6 inches (153mm) to 72 inches (65438+).
Operating steps:
1. Firstly, mark and locate the pipeline to determine the specific cutting position;
2. Lift the trolley with a forklift and put it on the pipeline to be cut, and the rotary cutting machine will aim at the scribing position for cutting;
3. Adjust the cutting trolley and tension the crawler chain to 65 n.m; ;
4. The hydraulic pipeline of the hydraulic pump station is connected to the corresponding position of the cutting trolley through the quick connector;
5. Power on the hydraulic pump station, adjust the cutter to the highest position, and add a certain pressure and flow through the remote control;
6. Start the run button on the trolley to make the cutting machine run at the required speed;
7. Adjust the cutter to cut down and slowly cut through the pipeline;
8. Turn the walking knob on the trolley to make the trolley cut and walk counterclockwise at a certain speed;
9. Pipe cutting is completed.
Split cutting beveling machine
Split cutting beveling machine
Splitting groove equipment is a pipe cutter developed by E-WORK according to the market demand and the needs of users in industrial and mining enterprises such as gas, oil and petrochemical enterprises. The equipment meets the requirements of related industries and the relevant standards and regulations of natural gas, oil and petrochemical companies. This equipment is suitable for pipeline cutting and groove maintenance in industrial and mining enterprises such as gas, petroleum and petrochemical. As a necessary equipment for users to install and maintain, it is suitable for various working environments: ditches, flammable and explosive, and narrow spaces where noise is prohibited.
Operating steps:
1. First, connect the upper and lower blades of the grooving equipment into a whole circle by inserting blocks, and tighten them with bolts to ensure that the V-lock on the retaining ring is inserted in place and fixed without gap. After installation, ensure that the pipeline is in the center of the equipment, and the bottom edge of the retaining ring is perpendicular to the outer contour of the pipeline;
2. The two tool holders are installed to the designated position of the moving coil through the positioning bolt column, and then pressed by the tool holder pressure plate;
3. The cutting knife and grooving knife are installed in the groove of the tool holder respectively, and pay attention to the installation requirements. See the above precautions for details;
4. The tool shifting device is installed at the corresponding position of the fixed ring and fixed and positioned with the jacking bolt;
5. Pull out the mounting pins on the upper turning plate and the lower turning plate, manually rotate the tool rest, and adjust the cooperation between the flywheel at the bottom of the tool rest and the tool shifting device until the tool shifting device can smoothly move the flywheel without being stuck;
6. When it is necessary to install the cutting knife and the groove knife at the same time, pay attention to that the cutting knife contacts the cut pipeline before the groove knife, and the groove knife contacts the pipeline 2-3 times later than the blade of the cutting knife;
7. Install the power source to the designated position, fix it in place with bolts, send electricity, start the power source, and pay attention to the rotation direction of the tool rest and the rotation direction of the power source (hydraulic) motor. If it is consistent with the rotation direction of the arrow, it is qualified;
8. It is advisable to measure the tool rest speed with 17RPM;
Second, the plastic pipe cutting tool pe pipe hay cutter
PE straw chopper
The series products of PE pipe mower are a series of professional cutting tools for cutting PE pipes produced by E-WORK. The structure design of the straw cutter is reasonable and simple. The fuselage is made of high-strength ductile iron, which has the technical advantages of high strength and strong ductility. Not only is it not easy to deform under stress, but it is also resistant to smashing and falling. The blade adopts high-strength tool steel and special heat treatment to balance the strength and toughness of the blade.
In addition, the surface of the blade is plated with Teflon coating, which not only ensures the rapid cutting of the blade, but also is durable and wear-resistant. It is a suitable cutting tool for cutting PE pipes at present.
Operating steps:
1, according to the diameter of pe pipe to be cut, select the appropriate model of PE pipe hay cutter.
2. Open the base of the straw cutter and put the PE pipe to be cut.
3. Adjust the relative position of the straw cutter and the PE pipe to ensure that the blade is in vertical contact with the PE pipe.
4. Rotate the operating handle of the straw cutter to make the feed screw advance slowly, and ensure that the blade descends vertically until the PE pipe is cut off.
5, reverse the straw cutter operating handle, make the feed screw slowly upward, until reset.
6, open the base, take out the hay cutter, and properly placed.
Rotary plastic pipe cutting machine
Rotary plastic pipe cutting machine
Rotary plastic pipe cutter series products are some professional cutting tools produced by E-WORK that can cut pe pipes. The product structure is reasonable and simple, and the fuselage is made of aluminum alloy, which has the technical advantages of high structural strength and light weight. Suitable for working pits and cutting on the ground, with only 6~8 inches of working space around PVC or PE pipes. The roller helps to calibrate the pipe cutter, and the dead cutting is straight. The pipe cutter can make a groove of 15 degrees both inside and outside the nozzle.
Operating steps:
1, check the blade to make sure it is not damaged.
2. Ensure that the longitudinal cutting knife and the cutting knife are retreated to the tool rest to avoid collision and interference with the pipeline to be cut, rotate the knurled spring seat and adjust the transition connecting plate, so that the rotary pipe cutter is fastened to the pipeline to be cut; Rotate the cutter blade to make the cutter in place, cut the pipeline to be cut by operating the handle rotating device, and rotate the cutter blade to make the cutter return to its original position after cutting; Rotating the blade of the cutter to make the cutter reach the cutting position, cutting the pipeline to be cut by operating the handle rotating device, and repeating the above operations after one revolution until the pipeline to be cut is cut; Then the cutter is returned by rotating the blade knob; Rotate the knurled spring seat to remove the equipment from the cut pipeline.
3. After cutting, put the equipment into the designated box and wipe it clean.
To sum up, we should be clear about the detailed classification, usage and specific operation steps of pipeline cutting tools. I hope my answer will satisfy you, and I hope it will be adopted!