How to install a toilet?
Toilet installation method 1. Before installing the toilet, check whether there is any blockage in the sewage pipes such as sand and debris, and whether the installation floor is level.
Toilet sewage pipes should use all plastic pipes required by national standards. The inner walls of the pipes should be smooth, flat, without bubbles, cracks, obvious marks and dents. In particular, be sure to ensure that the sewage pipe is about 10mm above the ground.
2. Determine the center of the sewage pipe and draw a cross center line. 3. Determine the center on the toilet drain outlet and draw a cross center line.
4. Determine the installation position of the bottom of the toilet, use an electric drill to drill the installation holes, and pre-embed expansion screws. 5. Install a special sealing ring (i.e. evaporated wax flange or rubber flange) on the toilet drain outlet or put a circle of glass glue (putty) or cement slurry around the drain pipe. The ratio of cement to sand is 1:3.
6. Align the cross lines on the toilet with the cross lines on the ground, install the toilet, and then put a circle of glass glue (putty) or cement mortar on the bottom of the toilet. The ratio of cement to sand is 1:3, and the toilet must be installed horizontally.
7. Screw on the toilet installation hole. 8. Install and debug water tank accessories.
After installation, connect the water source, check whether the water inlet valve and sealing are normal, check whether the drain valve and the installation position correspond to each other, whether the installation is tight, whether there is leakage, and check whether the length of the button switch chain is appropriate. , whether the switch is flexible, whether there is any chance of jamming, and whether there is any leakage of the water inlet valve filter device. 9. If any abnormality is found during the trial period of adjusting the toilet, please refer to "Common faults and treatment methods of toilet water tank accessories, check and deal with them".
10. After the toilet is installed, the glass glue (putty) or cement slurry should be solidified before water can be released. It cannot be used for three days after installation. At the current cement solidification speed, it will take at least one day to avoid using it, so as not to affect its stability.
.
What are the steps to install a flush toilet?
The steps for installing a flush toilet are as follows: 1. First we must choose the installation location.
According to the pattern and layout of the bathroom, determine the location for installing the toilet. It is best not to face the bathroom door; 2. The second step is to drill holes. Align the sewage outlet at the bottom of the toilet with the sewage outlet of the bathroom. There is a place for fixing the hole at the bottom of the toilet, and mark its corresponding position on the ground; 3. In the third step, we need to use steel expansion bolts to secure the toilet Positioning; 4. The fourth step is to drill holes in the wall and fix the water tank according to the size of the water tank and the position of the holes on the back wall of the water tank; 5. The fifth step is to use a connecting pipe to connect the water tank and the toilet.
A control valve should be installed at the connection of the water inlet pipe; 6. The sixth step is to install the float ball, water ladle and other accessories in the water tank; 7. The seventh step is to seal the gap between the toilet base and the ground. The sealing material can be putty or silica gel, but do not use cement mortar.
How to install a new toilet after buying it?
A. Installation begins after face-to-face acceptance of the goods: toilets should undergo strict quality inspection before leaving the factory, such as water testing, visual inspection of appearance, etc. Products that can be sold on the market are generally qualified. But remember, no matter how big the brand is, the goods must be unpacked and inspected in front of the merchant to check whether there are obvious defects and bruises, and whether there is color difference in each part.
B. Check and adjust the floor level: After buying a toilet with the same wall distance and a sealing cushion, you can start the installation. Before installing the toilet, you should conduct a comprehensive inspection of the sewage pipe to see if there is mud, sand, waste paper and other debris blocking the pipe. At the same time, check whether the floor of the toilet installation location is level. If the ground is found to be uneven, you should install the toilet. Ground leveling.
Cut the drain opening short and make it 2mm-5mm higher than the ground as much as possible if conditions permit.
C. After debugging and installing the water tank accessories, check for leaks: first check the water pipe and flush the pipe with water for 3-5 minutes to ensure the cleanness of the water pipe; then install the angle valve and connecting hose, and then connect the hose to the installed water tank Connect the accessory water inlet valve and connect it to the water source. Check whether the water inlet valve and seal are normal, whether the installation position of the drain valve is flexible and whether there is any jamming or leakage, and whether there is any leakage of the water inlet valve filter device.
D. Finally, test the sewage discharge effect of the toilet: the method is to install the accessories in the water tank, fill it with water, and try the flushing of the toilet. If the water flow swirls quickly and flushes quickly, it means the water is drained. If it is unobstructed, check if there is any blockage. .
What are the installation steps for a wall-mounted toilet?
Step 1: Adjust the height of the water tank. Side-press type water tank: According to the thickness of the decorative layer, the distance from the horizontal line in the white box diagram on the upper part of the bracket to the bottom of the adjustable foot of the bracket is 100cm Xcm.
Top-press type water tank: According to the thickness of the decorative layer, the distance from the top of the bracket to the bottom of the adjustable feet of the bracket is 82cm Xcm. The bracket adjustment legs can only be adjusted to a maximum of 20cm without special lengthening.
Step 2: Fixing screws The installation of the water tank bracket is mainly fixed by 4 screws, two on the upper part of the bracket and two on the supporting feet; at the same time, all screws on the water tank bracket must be tightened. During installation, ensure that the surface of the water tank support is horizontal and the elevation is vertical.
Step 3: Water supply pipe connection The water inlet of the water tank should be connected to the indoor water supply pipe (hard pipe) and the water inlet angle valve of the water tank. It is strictly prohibited to install the matching angle valve in the water tank outside the tank to avoid opening and closing the angle valve during cleaning and maintenance of the water tank.
It is strictly forbidden to use a hose to connect the water supply pipe and the water tank angle valve. The pipe pressure and the quality of the hose may cause leakage. In case of leakage, the false wall must be destroyed to repair it. Step 4: Drainage pipe installation. If the original pit location is used to install a concealed water tank, the short pipe connecting the water tank and the drainage pipe must be larger than φ90 to prevent clogging.
Step 5: Installation of protective devices Before making the false wall and installing the decorative layer, all protective devices should be installed. Install the screw protection hose, divide it into two parts, and put them on the front and rear ends of the screw respectively to avoid blocking the screw hole when building false walls or installing decorative layers.
Step 6: Make the light steel keel and moisture-proof gypsum board for the false wall. The surface of the light steel keel and the water tank bracket must be smooth. The water tank protection frame, flush pipe, drainage pipe, screw position, and gypsum board should be reserved on the gypsum board. The board surface must be close to the surface of the bracket and fixed. The water tank bracket should be filled with bricks or concrete below the elbow of the toilet to prevent the decorative material from cracking when the toilet is used because the gypsum board is not tightly attached to the bracket.
Gray bricks and steel wire mesh are used to lay bricks on the edges and gaps of the water tank bracket, keeping them flat with the surface of the bracket. Seal the water tank bracket as a whole with a steel mesh slightly larger than the bracket, and fix the steel mesh to the brick wall.
If necessary, two layers of steel mesh can be sealed. Red bricks: Seal the edges and gaps of the water tank brackets with red bricks. Build a 50mm red brick wall in front of the water tank. Reserve the water tank protection frame, flush pipes, drainage pipes, and screw positions.
The minimum thickness of red bricks is about 50mm. Step 7: The false wall decoration of the hanging toilet is completed, and the ceramic tiles have been pasted. Place the sound insulation pad on the decorative wall, measure and cut the pipe, and then install the toilet according to the position of the screw. The length of the screw exceeds the ceramic surface and fix the toilet. on the wall.
When installing the wall-mounted toilet, pay attention to adjusting the horizontal position of the toilet. After the installation is completed, cut off the excess sound insulation pad, and you're done.
How to install a bathroom toilet
① Before installing the toilet, conduct a comprehensive inspection of the sewage pipe to see if there is mud, sand, waste paper and other debris blocking the pipe. At the same time, Check whether the floor at the front, rear, left and right where the toilet is installed is level. If the floor is found to be uneven, level the floor when installing the toilet.
② Determine the center of the sewage pipe and draw a cross center line.
③ Turn over the toilet, determine the center on the toilet outlet, and draw a cross center line. The center line should extend to the feet around the bottom of the toilet.
④ If there are mounting locations for screws at the bottom of the toilet, it is recommended not to use it. First, it will damage the waterproof layer, and second, it will break the toilet if it is tight.
⑤ Install a special sealing ring on the toilet drain outlet.
⑥ Align the crosshairs on the toilet with the crosshairs of the floor drain outlet, install the toilet, press the sealing ring tightly, and then put a circle of glass glue around the bottom of the toilet , the toilet installation should be kept level from front to back, left and right.
⑦ Install or debug water tank accessories. First check the water pipe, flush the pipe with water for 3-5 minutes to ensure the cleanness of the water pipe; then install the angle valve and connecting hose, then connect the hose to the installed water tank accessory water inlet valve and press the water source to check the water inlet Check whether the water inlet and seal of the valve are normal, check whether the installation position of the drain valve is flexible and whether there is any obstruction or leakage, and check whether there is any leakage of the water inlet valve filter device.
⑧ After the toilet is installed, you should wait until the glass glue solidifies before draining it for use. The curing time is generally 24 hours.
Notes:
(1) When installing the toilet, please do not pour cement mortar into the cavity in front of the toilet or other cavities to avoid expansion and cracking due to cement solidification. Toilet feet.
(2) When using the toilet, please do not put newsprint, diaper pads, sanitary napkins and other easily clogged items into the toilet.
(3) The toilet cannot be used in a water environment below zero degrees Celsius, otherwise the water will freeze and expand and the ceramic body will be crushed.
(4) To prevent breakage and water leakage, please do not hit the ceramic with hard objects.
5) To keep the product surface clean, please use a nylon brush and soapy water or neutral detergent to clean it. It is strictly forbidden to use steel brushes and strong organic solutions to avoid damaging the product glaze and corroding the pipes.
That’s all. Haha, I’m also in the process of renovating. When I went to the market, I saw that better toilets were very expensive, so I planned to buy them online and install them myself. This is what I summarized and excerpted, and it took me a long time to do it. I typed it up for you to see, I hope it will be helpful O (∩_∩) O~
Detailed diagram of how to install a toilet
1. Make the ground drain outlet as high as the ground. Then press the center of the nozzle to draw a cross extension line.
2. Draw a cross line along the toilet outlet to a position where it can be seen on the edge of the toilet.
3. Place the horse pass to the drain outlet, with the cross lines overlapping.
4 Draw a line along the outside of the toilet and move it away.
5. Place the toilet sealing flange on the drain outlet on the ground, and apply glass glue along the inside of the drawn overall circle line of the toilet.
6 Place the toilet with the crosshairs overlapping, press the bottom edge of the toilet on the glass glue, connect the water supply hose, and install an angle valve at the water outlet on the wall to facilitate future water shutoff and maintenance. .
7 Do not use, keep the ground dry for 24 hours.
I hope it helps you, thank you