In fact, showers are formed of two parts, the sensor and the solenoid valve nozzle, and the induction shower can also be divided into two specifications: concealed installation and surface installation. Below, the editor of Tubatu will take you together Learn about the main functions and features of induction showers.
The main functions and characteristics of the induction shower:
1. Water saving, it automatically senses the coming and going of the human body, and the water stops when people come and go. The water saving effect is very obvious, reaching 30%---more than 50%.
2. Hygiene, the water will flow out when people arrive at the nozzle, and the water will stop when people leave, effectively eliminating bacterial cross-infection.
3. Waterproof, fully sealed with epoxy resin and long service life.
4. Anti-fog, anti-fog technology in winter, especially suitable for places with low temperatures in the north.
5. Near objects, the patented anti-obstruction function of near objects prevents constant water flow caused by artificial obstruction of near objects.
6. Easy to maintain, the nozzle has strong anti-scale and anti-fouling functions. There is an easy-to-remove filter at the water inlet, which can be easily maintained by non-professionals.
7. Intelligent. The sensor is controlled by a microcomputer. The sensing range has been set at the factory and does not require manual debugging.
8. Safety. This product uses 24V safe DC power supply, which is safe and reliable. The shower elbow adopts an upper water outlet design and is fixed by a special bracket to prevent malicious pulling and damage by humans.
9. Easy to install, suitable for a variety of new and renovated baths.
Installation and use of induction shower:
Steps: Design water supply pipeline→→Install water supply pipeline→→Set power supply circuit→→Pipeline flushing→→Fix the base plate→→ Connect the power supply line→→test with water and adjust→→use.
1. The power supply of the induction shower must be dry, and it must be safe and convenient for people to press. Note that the distance between the power supplies should be <50M, and each power supply must be independent and cannot be connected in parallel.
2. When the main power cord passes through the three-way junction box, a 4cm long U-shaped bend should be left. After peeling, connect the randomly delivered power cord according to the red, positive and black polarity. The connector should be waterproof Wrap the tape tightly, and remove the end of the power cord with the waterproof plug for use.
3. When installing the induction shower, be sure to set the base plate. It is best to mark the outer edge of the base plate at the fixing holes, and then drill 4-6 holes with a depth of >29MM. ?, and then fix the bottom plate. When tapping the tiles, remember to tape around the holes to avoid damaging the tiles and to ensure the holes go straight in.
4. At 25 cm above the bottom plate, align the fixing base in the center of the water outlet pipe, then drill two Ф6 holes and insert a Ф6 plastic expansion plug.
5. If the power supply is open-wired and the water is supplied at a constant temperature: Install a φ16mm PVC conduit under the three-way junction box, and its length can be aligned with the upper edge of the bottom plate. Thread the power cord into the line. In the pipe, use the water inlet pipe that comes with the machine to connect it to the main water pipe; then put the fixed seat into the water inlet pipe and line pipe in sequence, and use 2 M4×30 stainless steel self-tapping screws to fix the fixed seat on the wall.
6. Insert the power cord that passes through the PVC conduit into the base plate through the notch on the side of the water inlet pipe of the base plate, and then connect the two plugs of the controller to the power cord and solenoid valve line respectively. Because it is used in a humid environment, the waterproof plug must be plugged in tightly. Then buckle the shell from top to bottom, and screw on two M4×8 stainless steel self-tapping screws on the lower end of the shell to fix it to the bottom plate.
7. Pass the upper decorative plate through the water outlet and water inlet at the same time, and press it firmly into the top of the shell; then smooth the water inlet, put a 4-point rubber pad on it to connect it to the water inlet; and then lock the water outlet pipe. The lock nut is slid from the upper end of the water outlet pipe to the snap ring. Put a "tapered rubber ring" on the lower end of the water outlet pipe, insert it into the water outlet, and lock the lock nut; put the upper end of the water outlet pipe on the fixed seat, and use Press the fixed cap and fix it with 2 M4×15 stainless steel self-tapping threads; then assemble the shower head, put a 4-point rubber pad on it and screw it to the water outlet.
8. Paste the "Usage Tips". Clean and dry the wall before pasting. Be sure to paste it straight, flush and flat.
9. Check the pipeline again. If it is correct, turn on the water first, observe whether there is water leakage, and deal with it properly; then turn on the power and test the nozzles one by one to see if they can sense and discharge water normally, and stop water.
Induction showers have many advantages and are the pursuit of modern people’s lives. They are not only water-saving and safe, but also very unique and individual. They are the fashionable pursuit of young people today. Today, the editor mainly introduces induction showers to you. The main functional features of the shower, as well as the installation and use instructions of the attached induction shower, are provided for your reference.
Tubatu provides you with "each decoration quotation, 1-4 local decoration companies, 3 sets of decoration design plans" online for free, as well as decoration avoidance strategies! Click this link:/yezhu/zxbj-cszy.php?to8to_from=seo_zhidao_m_jiare&wb, and you can get it for free~