(1) ***Requires 10 scheduling seats, two seats in a group, each seat supports two 22-inch monitors, ***Needs to support 18 22-inch 16:10 monitors Equipment, the monitor is suspended on the back panel of the console through the monitor arm. The height of the back wall is 320mm. The back wall is made of aluminum structure. The surface has been treated with wear-resistant electrospraying, anti-static, and has grooves for easy hanging of the monitor arm.
(2) Each seat is equipped with a host tray that can hold the computer host. The keyboard, mouse, and monitor are connected to the computer room host through the KVM extension device. It is equipped with an easily removable partition to facilitate the placement of the KVM extension device. wait.
(3) The console *** needs to provide 8 6-position 3-hole PDU power supplies.
(4) One information interface for every three seats, pop-up style, including 2 telephones, 2 networks, 1 VGA, 1 3.5 audio interface, 2 power interfaces, and 1 microphone interface .
(5) The length of each group of seats is ≥ 6 meters. (1) The design of the dispatching console should be based on the actual situation of the tenderer, with a reasonable layout, beautiful appearance, high usability, and compliance with safety regulations and ergonomic requirements. The configuration should be based on the actual area and size of the control center and the rationality of the spatial layout. design, and should take into account coordination with the overall environment.
(2) The dispatching console is flexible in installation and maintenance. The overall design adopts a modular design to facilitate disassembly and future expansion.
(3) The internal structure has greater flexibility. Adjustability, supplemented by professional various equipment support brackets and internal accessories, making installation and adjustment more convenient.
(4) The internal frame of the dispatching console has cable through holes, or an equivalent cable management system, which can be placed in different locations to make wiring convenient and orderly.
(5) The non-metallic materials used for the table and main body should have fire-retardant properties, and all materials are made of environmentally friendly materials to ensure the health and safety of operators. The console top material complies with the international standard GreenGuard certification.
The adhesive used on the workbench should be adhesive that meets national environmental protection requirements.
The painted materials used on the workbench should be free of VOC (volatile organic compounds) emissions.
The console should have an inspection report issued by the National Furniture and Indoor Environmental Quality Supervision and Inspection Center.
The console should obtain environmental management system certification.
The console should comply with occupational health and safety management system certification. The console frame should meet the standards shown below, (width can be adjusted according to the size of the built-in 22-inch display).
(1) Main frame
The main frame includes left and right side windows, upper and lower beams; it is connected through universal connectors to form an independent module, and the common components between the modules are consistent and mutually accessible. After replacement, the modules after the overall connection are internally connected, and various cables can be freely connected in the console.
(2) Rear beam
A load-bearing rear beam is installed at the rear of the main frame, and the thickness of its sheet metal parts is not less than 3mm
(3) Back wall
The back wall is fixed on the rear beam and the groove plate for hanging the display arm is processed using an aluminum alloy profile with a cross-sectional thickness of not less than 2mm. The entire back wall is connected to the main frame and rear beam through square tubes with a size of not less than 25mm*25mm. The cross-section thickness of the square tubes is not less than 2mm. They will be integrated after installation.
(4) Large panel support arm
The table panel load-bearing support arm is installed on the front of the main frame, and the thickness of its sheet metal parts is not less than 3mm.
(5) Neutral column
A neutral column is used to divide the internal space in the middle of the longer linear module. The door panels are installed on the neutral column and side windows in a hinged or suspended manner. Behind the neutral column Can place six three-hole PDU power modules.
(6) Accessories
Install the host tray inside the module. Distribution frames, PDUs, and CarboFi bridges can be configured according to needs. A round hole for installing 86 boxes should be reserved every 6 inches on the upper beam to facilitate the installation of various strong and weak electrical interfaces.
The round hole for cable entry in the lower beam needs to be installed with a plastic cable sheath to prevent the cable from being scratched. The lower part of the table can be equipped with single or double-layer keyboard racks.
(7) Materials and processing
Each component in the frame structure is stamped and bent using first-grade cold-rolled steel plates, and the main frame uses first-grade cold-rolled steel plates with a thickness of not less than 2mm. Processing and load-bearing beam components are made of first-class cold-rolled steel plates with a thickness of not less than 3mm, and the outer surface is sprayed with electrostatic plastic powder.
(8) The front and rear door panels of the main frame
The front and rear door panels of the frame are made of solid wood particle board and double-coated with imported fireproof boards. The overall thickness is not less than 20mm. The connecting hinges use high-end silent buffer hinges. During installation, it should have the advantages of light weight, good feel, and low noise when opening and closing the door, ensuring that it can be opened without hindrance 100,000 times. At the same time, the hinge installation method must be quick-installation and easy to install and disassemble.
(9) Depth range
The depth requirement of the dispatching console is in the range (1000-1100mm).
(10) Error requirements
Linear ±0.5 mm (including this number);
Vertical ± 0.5° (including this number). The surface covering should be made of high-strength high-pressure wear-resistant plate (HPL) that is heat-resistant, smoke-resistant, impact-resistant, moisture-resistant, waterproof, and corrosion-resistant. The rear panel should have sufficient support to ensure lateral stability. The panel part is a monolithic structure, and each part should be integrated with the entire structure. The control panel of the console shall be removable without the need for any tools.
(1) Operating table top structure
The operating table top is divided into two parts: large and small panels. Leave a gap of no less than 10mm between the small panel, the back wall, and the large panel to facilitate the cable outlet from the bottom of the main frame to the countertop.
The small panel is the front access panel, which is made of solid wood particle board and double imported fireproof board. The overall thickness is not less than 20mm and is connected to the main frame through a plastic snap-on connection. A pop-up stainless steel button is installed on the front, making it easy to remove the small panel for maintenance.
The large panel is made of solid wood particle board and double imported fireproof board. The overall thickness is not less than 27mm, and there is an opening between the two large panels. For the arrow groove, use a tie rod no less than 100mm long and no less than 6mm thick to connect both ends. The overall connection must be flat, smooth and seamless.
(2) Large panel edge banding process
Use a soft polyurethane duckbill curved edge banding strip of no less than 30mm wide at the front end of the large panel in contact with the human body to ensure the operator's work The arm feels natural and comfortable. A soft polyurethane edge strip of no less than 6mm thick is used on the rear end surface. After installation, the overall height is 8mm higher than the countertop to prevent pens and other stationery from slipping.
The formaldehyde emission of solid wood particle boards used in panel, door and cabinet products must comply with national standards (a test report issued by a formal testing agency must be provided)
Operation desk product structure, Appearance, application of various materials Bidding companies must have independent intellectual property rights, and must provide relevant patent certificates
(3) Working surface and panel table
Working surface: 1 inside (25 mm) composite panel with high pressure HPL surface.
Table edge: formed by casting flexible polyurethane on the periphery, with a width of not less than 30mm.
The front of the device: (the interior is 18mm solid wood particle board), the surface is high-pressure HPL, and hinges must be used to simplify installation.
Working surface width: 450 mm -800 mm;
The distance from the surface to the ground is: 720-750 mm, and the bottom adjustment feet can finely adjust the height;
Working Table support arm: The material strength standard is no less than No. 10 cold-rolled steel; the strength standard of the reinforcing rod is no less than No. 12 cold-rolled steel.
Bottom support: bending stress is not less than 110 KSI.
HPL covering layer: rated thickness: not less than 1.2 mm; thickness error: within ± 0.12mm (including this number); wear resistance: not less than 400 cycles. Most of the main structure of the lifting monitoring station adopts the same structure as the ordinary monitoring station.
The main parts of the monitoring operator (desktop, keyboard control, monitor stand) adopt an electric lifting control structure.
Technical parameters: The frame structure of the monitoring station is made of 10 Gauge (3.429mm) cold-rolled steel plate, which is processed by stamping and CNC (CNC machine tool) positioning and drilling to make the structural frame. These structural frames are stretched to form a polished, rectangular structure.
The main support frame is made of 10Gauge (3.429mm) cold-rolled plate material; the auxiliary frame is made of 12Gauge (2.667mm) cold-rolled plate material.
The manufacturing error is controlled at: linear ±0.5 mm; vertical ±0.5°
The main frame structure is also composed of the same module design principles as ordinary workstations, including bends and angles;
The design of various structural frames meets the requirements of ergonomics;
The installation position of the monitoring station equipment and the cable management system are specially designed to facilitate the installation and use of the equipment. , adjustment, and the layout of various cables;
Monitoring desk desktop: The desktop board is made of 1" thick density board, and the surface is covered with HPL high-pressure wear-resistant fireproof board (1.2mm); the edge of the table is made of polyurethane Soft-wrapped edges, in line with ergonomics, ensure the comfort of monitoring personnel working for a long time;
Automatic lifting structure: The lifting part of the monitoring table uses a low-noise motor, which can smoothly raise the desktop and display equipment ;
The motor has a compensation system to prevent stepped uneven movement; the monitoring desk lift has a load of 2500N (550lb or 249.5kg). The monitor arm is required to withstand a load of no less than 18kg and should have an extension function. Capacity.
The base of the monitor hanging arm should be able to be positioned and fixed in any position without the use of tools. /p>
It can meet the requirements of single-layer and double-layer display installation, and double-layer overlap does not affect the stability of the display installation.