Hello, it seems that no one will take a look at this and can I help you. Operation notes:
1) When reading the disk, if it is not smooth, you can turn off the power again and plug in the USB port. , if you use Huaxiang controller, you can first switch the storage and reading media (U disk and disk) and then turn on the computer to read the disk.
2) When threading yarn, adjust the antenna elasticity and side antenna tension.
3) Adjust the pattern according to the proofing requirements. Pull force etc.
4) Determine the pattern unfolding and yarn feeder position. The National Flower series also has pre-production capacity.
5) Hang the cloth (not used on the bottom plate machine), lock the row (repeat for the Feihu machine) and immediately give the auxiliary roller closing status. The machine head speed should be less than 0.40m/s, and the cloth piece reaches Release the row lock when the main roller is turned (click the Feihu machine handle repeatedly). Increase speed, pull force, etc.
2. Start knitting
1) Check the density of the fabric pieces and confirm the condition of the thick and thin yarns at any time, so as to control the length of the pieces at any time. Follow sample size.
2) Pay attention to the waxing condition of wool yarn and the discharge position of wool yarn. When disassembling the yarn, re-test the mesh and tension.
3) Keep informed of yarn usage, wool color difference, etc.
4) The shirt pieces are divided into codes, and the colors are neatly folded and bundled for delivery.
5) Pay attention to the rewinding cloth and auxiliary roller yarn (especially the national flower series)
3. How to deal with common problems
(1) Objective
1) The mesh becomes larger and larger when knitting
A. Check whether the circuit is in poor contact.
B. Check whether the motor screws are loose.
2) Two ends are knitting at the same time. If the mesh in one end is abnormally small
you can consider adjusting the origin of the mesh to a larger size.
(2) Bump the connecting pins (the National Flower series is called long pins)
1) Check whether the stitching is flexible.
2) Check whether the connecting pins run smoothly on the needle bed, and whether they can spring up freely when pressed by hand
3) Check whether the screws of the mesh motor are loose. Check whether the turntable is smooth.
4) Check whether the eye sensor is damaged.
5) Check whether the three pins of the pressure needle are in place. The National Flower series depends on the swing of the electromagnet.
6) If the mesh is too tight, it cannot come out of the loop and the connecting pins will be hit.
7) Check whether the needle guide block of the needle transfer triangle is smooth and flexible.
8) Check the bottom plate and whether the slider is in place and flexible.
(3) Random stitching (random needle selection)
1) Check whether the random stitching on the fabric is regular, for example, which needle selector is the problem.
2) See if it is a stolen selection or a missed selection. Adjust the gap between the needle selector and the needle bed.
3) Adjust needle selection parameters, needle selection origin, and needle selection fine-tuning.
4) Check whether the needle selection stitch is too tight or too loose on the needle bed. Is it smooth?
5) Check the circuit to see if each plug is plugged in properly and see if there is any poor contact.
6) Check whether the main drive belt is too loose.
7) Check whether the needle ruler is too tight or too loose.
8) Replace the needle selection substrate.
9) Re-find the origin, and pay attention to the copper head part of the National Flower series.
(4) Flat swing missing needle
1) Check whether it is caused by random printing
2) Check whether the installation of the sky pole is standardized, which may cause the yarn feeder to be high or low , whether to align with the middle seam of the mouth hole.
3) Check whether the knitting needle is not smooth on the needle bed.
4) Check whether there are any problems left over from the previous row of needle transfer.
5) Check whether the knitting needle is damaged
(5) Oblique piece
1) If the oblique piece is used to determine the tension of the cloth, the reason for the square position of the wool yarn back. Lower the needle plate on the longer side of the fabric piece and raise the needle plate on the shorter side.
2) In special circumstances, the problem of moving guides can be considered
3) The above two methods should consider the "turning position"
(6) Turning Needle
1) Check whether the needle transfer position is correct.
2) If the transfer position of the same port's transfer machine head moving to the left and moving to the right are too different, check whether the transfer triangle is standard at the butterfly mountain.
3) If the needle transfer position is correct, some knitting needles are too high or too low, and the hole positions are too different, the needle plate needs to be lowered and repaired until it is standard.
(7) Tuck yarn spinning
1) Check whether the knitting needle is replaced incorrectly (for example, 12 needles are replaced by 14 needles instead)
2) If the knitting needle is not replaced correctly, If the gap between the needle exit and the distance between the mouth and mouth is affected, raise the needle plate.
3) The density is too loose.
4) The pulling force is too small, and the antenna and side antenna are not elastic enough.
5) Check whether the butterfly mountain is the old type of butterfly mountain.
6) Check whether the flip-up guard is installed incorrectly.
7) The Xinke is not pressed in place, and the movable teeth (sinkers) lift the yarn.
(8) Knitting covered needles
1) The knitting needle is damaged and the needle latch is inflexible
2) The mouth is too large
3) The density is too tight
(9) There is abnormal noise during knitting
1) The main drive belt is too loose or too tight
2) Check the machine head slide Whether the block is crooked
3) Whether the distance between the mountain plate and the pin plate is standard
4) Whether the insert is flat
5) Whether the screws of the Xinke fixing plate are in place with the Xinke There is friction in the base.
6) Check whether the fixing screws of the machine head plate are loose.
7) Is the clearance between the bearing and the guide rail standard?
8) Whether the needle path of the knitting needle is smooth.
9) Is the mesh stuck?
10) There is an abnormal sound when the yarn feeder is running, maybe the drum is not locked properly.
11) Whether the yarn feeder touches the needle hook or needle latch from the bottom, and whether the yarn feeder screw is loose. (10) When knitting the tuck, the tuck is knitted instead of hanging, and the needle triangle is not pressed in place.
(11) Hitting the needle selection pins
1) Whether the needle selection returns to the correct position
2) Whether the needle groove runs smoothly and whether there is iron in the needle groove The idle running time must be sufficient and the speed cannot exceed 0.45
3) Is the pin model wrong?
4) The distance between the mountain plate and the needle plate is too large, more than 40 lines
p>
5) The gap between the guide rail and the bearing is too large.
(12). Display main motor error
1) Poor circuit contact
2) Replace the main motor
3) Speed When it is too large, it is displayed and the drive needs to be replaced.
(13). Display shaker motor error
1) Check for poor circuit contact
2) Turn off the power and restart the machine
3) Replace the shaking bed motor
4) Replace the shaking bed driver
(14)
When the knitting needle is pushed over and turned over, it is not smooth
1) The transfer wire needle is too tight
2) The needle plate slot is milled too deep
3) The needle ruler is too tight or deformed
4) The knitting needle is deformed
5) Whether the fixed tooth spacer is installed incorrectly.
(15) Fixed knitting needles are not selected or missed during normal knitting
1) Adjust random patterns
2) Replace needle selection stitches< /p>
3) Adjust the yarn feeder correction
4) Reversal the machine head left and right,
5) Without affecting the needle transfer, if you do not select the mountain Board. Missing selection, downhill board
6) The spacing between the inserts is too tight, use a screwdriver to loosen it
7) Swap the needle selector
8) Lower The needle ruler is too tight or too loose
9) When it appears on both sides, check whether the origin of the machine head is correct.