Question 2: What exactly does "on-site palletizing" mean in logistics? How to understand it generally refers to random stacking in the workplace! Suitable for scattered, sharp turns and goods to be processed. If the shoes are sent to the store, they will be piled up on the spot. After the documents are processed, they will be displayed on the shelves according to the owner's preferences.
Question 3: What exactly is a stacker? All I know is that it is packaging equipment. . . Palletizing is a device for stacking bags or boxes on a pallet layer by layer.
It is divided into high-position palletizing and manipulator palletizing.
German Berman made it very well.
Question 4: Briefly describe the similarities and differences between palletizing robots and handling robots. You can refer to official website, a scout robot. The palletizing robot and handling robot are introduced respectively, and the detailed technical parameters and functions are given.
Question 5: What does palletizing mean?
English ['p? lta？ z]
Beauty [p? lta？ z]
[Dictionary] Stacked with plywood;
[Example] Full-time automation of bottle making, filling, labeling, robot, packaging and palletizing was realized, and polarization of any link was avoided.
It realizes the full-time automation of packing and palletizing of bottle blowing machine filling and labeling robot, and avoids pollution in any link.
Question 6: How do forklifts stack 1 correctly? What is the "five forks" of forklift drivers? (Contact: Teacher Sun 17784462669)
Answer: (1) If the center of gravity of the goods exceeds the load center of the fork, it will not fork when the longitudinal stability decreases.
(2) A single fork does not bifurcate under unbalanced load.
(3) The goods are stacked unsteadily and not forked.
(4) Don't fork when the fork tip may damage the goods.
(5) Overweight or unknown weight.
2. What are the rules for forklift truck operation?
Answer: When the forklift is working, it is forbidden to lift and pull goods and overload the forklift. Forklift is forbidden to carry people, and electric forklift is forbidden to connect two action circuits at the same time. The stacking height of each stack in warehouses and cars shall not exceed four boards. When forklifts fork fragile, valuable or unstable goods, they should be reinforced with safety ropes, and they can only run when necessary.
3. Under what circumstances should the forklift slow down?
Answer: Turn, retreat, narrow passage, uneven road surface, traffic intersection, slow down when approaching goods.
4. What are the requirements for forklift trucks?
Answer: The forklift truck should drive to the right, and the fork should be 200 ~ 300mm above the ground. When forklift trucks want to avoid empty cars and heavy cars, downhill cars avoid uphill cars, branch lines avoid trunk lines, and big bends avoid small bends. When entering and leaving the car door and garage door, let the car leaving the garage door go first.
5. What items should be checked when the diesel forklift shifts?
Answer: Check whether the fuel, engine oil and cooling water are sufficient, whether the fan belt is tight, whether the wind window is unobstructed or cold-proof in winter, and whether the tires are inflated and tight. Start trial operation and check the operation of steering and braking (including hand braking) working mechanism.
6. What is the content of forklift daily maintenance?
Answer: (1) Wipe the dust from all parts of the machine. (2) Check the engine oil quantity (internal combustion forklift). (3) Check the specific gravity and height of the battery electrolyte. The height of electrolyte should be higher than that of separator10 ~15 mm. Tighten the plug and check whether the electrode and wire connector are fastened. (4) The free travel reliability of the clutch and brake pedal, and check whether there is oil leakage in the oil circuit. (5) Whether all kinds of electrical circuit connectors are firm and whether all kinds of instruments are sensitive and effective.
7. What is the content of the labor safety code that all employees abide by?
Answer: 1. Four qualities: to have a full rest before work, to concentrate on work, to use protective equipment correctly, to cross the line, to stop, to look at and to pass three tests.
2. Article 7: Do not leave your post without permission, fly, ride, ride with the car, drill over the car, rush over the line, and ride on the sleeper wood and the center line of the line.
8. What are the safety requirements for forklift trucks working in boxcars?
Answer: When there is no platform outside the boxcar, the doorway should not exceed the width of the forklift, otherwise it should be protected. The joint between the platform and the car should be provided with a crossing board. Its slope shall not be greater than 20%. When the floor in the car is rotten and damaged, it is necessary to lay steel plates.
9. What safety regulations should be observed when forklift trucks are engaged in dangerous goods operations?
Answer: Ordinary forklifts are not allowed to operate inflammable and explosive articles in dangerous goods; Handling machinery for toxic and radioactive substances of dangerous goods should be used with 25% load reduction, and should be handled with care during operation, and violent vibration such as bumping, bumping and dragging is prohibited.
10. What should the driver pay attention to when replacing the battery?
Answer: (1) Pay attention to the polarity of terminals and poles when wiring;
(2) When wiring, be careful not to touch the body with the wrench;
(3) The terminal should be clean and the joint should be fastened.
1 1. What are the technical requirements for "lifting" in forklift operating standards?
Answer: The following technical requirements should be met when starting the car: (1) The gantry leans backward. (2) Lift the fork 0.2~0.3m above the ground; (3) Look out and whistle. (4) Start in the first gear, and shift gears with one lever and one lever. (5) Steady acceleration.
12. What are the safety technical requirements for forklift parking?
A: It is forbidden to park on the ramp or on the side of the platform perpendicular to the line. When you can't walk in case of failure, you should tighten the handbrake and cover the wheels with triangular wood before troubleshooting.
13. What should I pay attention to when parking the forklift after operation?
Answer: After the operation is completed, the forklift should be parked in a place that may block traffic, and try to avoid parking in the open air. When the driver leaves the forklift, he should remove the key on the electric lock, cut off the power supply and set all the control handles to zero. When the fork reaches the lowest point, the gantry leans forward. When it is necessary to park on the ramp, the forklift must be braked by the hand brake mechanism, and a stop wheel is added to prevent it from slipping.
14. What are the stacking requirements for vehicle cargo and LTL cargo?
Answer: The stacking of vehicle cargo and LTL cargo should be smooth and tidy, and the vehicle cargo should be kept at a certain height to achieve fixed stacking. Less-than-truckload goods should be stacked in batches with labels facing outwards, so that they will not be heavy ... >>
Question 7: What does 20k g in 20kg aluminum ingot stacker mean? 100 minute, 20KG is 20KG, and KG is KG.
Question 8: Can the automatic mechanical stacker only be used as a stacker? How big is the gap between domestic and foreign countries? Many palletizers are called palletizing robots, which are mainly composed of control units and action units. The quality of the stacker is mainly the difference between these cores. Compared with foreign countries, domestic automation equipment is backward. Moreover, foreign robots may not be called palletizers, because palletizing is only one purpose of robots, and foreign robots can achieve more functions, mainly because the accuracy of domestic palletizers is not enough, and many special positions are not competent. (For more information, please visit hfxykj)
Question 9: Does the robot use suction cups or claws to see the stacked objects at the end of stacking? Generally, the suction cups are used for tray loading.