It is very important to accept the renovation of new houses if you want to live in peace of mind.
New house decoration acceptance process:
I. Hydropower
The first thing is to check whether the water and electricity in the house are connected. Wire inspection, in addition to seeing whether it is electrified, mainly depends on whether the wire meets the national standard quality. Then there is whether the cross-sectional area of the conductor meets the requirements. Generally speaking, the wires in the home should not be less than 2.5 square meters, and the wires in the air conditioner should reach 4 square meters. Otherwise, when using air conditioning, it is easy to overheat and soften. Of course, this is an ideal configuration, and most civil lines will be one grade behind.
Second, the waterproof test
Waterproofing here refers to the waterproofing of kitchens and bathrooms. If you don't try it before the renovation, then if you find water leakage after the renovation, then the maintenance project will be big. You have to tear down the newly decorated floor to make a new waterproof layer. The waterproof acceptance method is: use cement mortar as bottom beam to block the toilet door, then cover the sewage/water outlet with plastic bag, then tie it up, and then drain the water in the toilet, as shallow as possible (about 2cm high). Then make an appointment for the owner downstairs to check the smallpox in his toilet 24 hours later. The main leakage parts are: direct leakage of the floor; Contact between the pipe and the floor.
Third, check the pipeline.
The pipes mentioned here refer to drainage/sewage pipes. Especially seven is the balcony and other sewage outlets. At the time of acceptance, take a water container in advance and then pour the water into the sewage outlet. See if the water flows smoothly. Why do you accept this? Because during construction, workers often cut corners while cleaning. Pour some cement residue into the drain pipe and drain it away. If the cement is sticky, it will block at the elbow, which will make drainage difficult.
Four, the house should be no cracks.
1, carefully check the floor and roof of the house for cracks. If there are cracks, it depends on what kind of cracks. Generally speaking, although the cracks parallel to the beam are quality problems, they are basically not dangerous and will not hinder the use after repair. If the crack is at an oblique angle of 45 degrees to the corner or perpendicular to the beam, it shows that there are serious settlement and structural quality problems in the house.
2. See if there are cracks on the exterior wall of the house. If there are cracks, it is also a serious quality problem.
3. See if there are cracks in the load-bearing wall. If the crack runs through the whole wall and passes through the back, it means that there are hidden dangers in this house. For this kind of house, buyers must not report luck.
5. The house should not be tilted.
You can tie a heavy object on the roof with a string, stick it on the wall and put it down to the foot of the wall, and check its inclination from all sides.
If you want to live in peace of mind, it is very important to accept the renovation of the new house.
Six, the house should be no leakage phenomenon.
Property buyers should pay attention to the water seepage on the ground and top floor of the house, and carefully check whether the wall surface of the house is discolored, blistered, peeled and dusty, which are all signs of leakage. You should also check whether the kitchen, bathroom, balcony roof and pipe joints are leaking.
Seven, check the quality of metope and ground.
1. For the blank house that has been handed over, check whether the wall is flat and there can be no obvious ups and downs. Looking at the wall has become the primary problem of house acceptance. Acceptance of this, it is best to check the house before the delivery, the day after the heavy rain. At this time, if there are problems with the wall, it is almost inevitable. In addition to water seepage, there is another problem, that is, whether the wall is cracked.
2. Check the wall for lime "explosion". If lime is not cured for enough time, or there is too much silt in cement or uneven mixing, when the "explosion point" is hit by iron, there will be quality problems such as looseness and falling off in a large area.
3, the ground should be bright and clean, can't sand.
4, check the kitchen, bathroom wall brick masonry is qualified, brick can't have cracks, can't empty drum, must build by laying bricks or stones.
Eight, check the doors and windows
Mainly based on the acceptance window, the focus of acceptance is the sealing of the acceptance window and balcony door. The most troublesome thing about window seal acceptance is that it can only be tested in rainy days, but it can generally be confirmed by checking whether the sealing strip is complete and firm. The balcony door generally depends on the level difference between the inside and outside of the balcony door. I have seen a situation where the elevation of the balcony is the same as that of the interior, and it is difficult to avoid the problem of rainwater infiltration in rainy days. Whether the compactness of doors and windows is appropriate, whether the opening and closing are smooth, whether the vulnerable parts such as the edges of door frames and window frames are dense, and there should be no gaps.
The article is reproduced from the official media or other websites, and the copyright belongs to the original author. The purpose of reprinting on this website is to spread the information more widely and give full play to its value. If copyright issues are involved, please contact our website, which will handle them as soon as possible after verification. QQ Group for National Owners Exchange: 573032185; Wechat: wx 17house pays attention to politeness and gets tips on saving money.