If it is an ink cartridge printer, l101/201/8065438+
When the red light is always on and the actual ink amount is not less than 20mm, click "Start" in the lower left corner of the computer-> "devices and printers" or "printers and faxes", right-click the icon of the printer used and select "printing preferences"->; "maintenance"->; "EpsonStatus Monitor", click "How to", click "Continue" according to the screen prompts, and then close the window. At this point, you can continue printing. When the ink in the ink cartridge is less than 20mm, replenish the ink and enter the ID number.
You can continue to use the printer when the ink light goes out or flashes. If the actual amount of ink is less than 20mm, it is recommended that you replenish ink (take care of the ink bottle). When the ink light is on, click "Start" in the lower left corner of the computer. > "devices and printers" or "printers and faxes", right-click the icon of the printer used and select "printing preferences"->; "main window"->; "EpsonStatus Monitor", click "How to", and follow the on-screen prompts to enter the ID number on the ink cartridge.
If it is a printer with other ink cartridges, such as L 211/L 351/L353/L358, when the ink lamp is always on, please fill it with ink (it is recommended to fill all ink cartridges with four colors), and then press the maintenance key (inverted triangle key) of the printer, the ink can be reset and the ink lamp will go out.
Tip:
1. Please pay attention to the ink capacity of the ink cartridge. When the ink capacity is less than 20mm, please replenish the ink in time to avoid the failure of the print head.
2. The ink light is always on. If there is no response when pressing the maintenance key, please press and hold the printer's maintenance key (inverted triangle key) and gently knead it twice.
Question 2: How to add ink to Epson printer? Most Epson printers are suitable for continuous ink supply, which is too troublesome. In addition, the capacity of Epson ink cartridge is not very large, and it will be very frequent if ink is added. If you use too much, it is recommended to change it directly to continuous supply. If not, you can choose to add ink. The method of adding ink is to punch a hole on the surface of the ink box, and inject ink into the sponge in the ink box with a syringe, 5-8ML each time. Then seal the hole with a sticker.
Question 3: How to add ink to HP printer? Hello, thank you for choosing HP products.
The HP ink cartridge itself is a disposable design. If you go back to the replenishment kit, replenishing ink will damage the ink cartridge and endanger the hard function of the printer itself, and the replenished ink cannot guarantee the printing quality. It is recommended that you replace the ink cartridge directly after use. If the above information can't solve your problem, you can consult an engineer online by asking questions or HP technical support chat rooms. Thank you for your support to HP.
I hope the above reply can help you.
Question 4: How to enter the code after adding ink to Epson printer? Please confirm your printer model first, whether it is (L 10 1, L20 1, L30 1) printer.
1. You can click "Start->" in the lower left corner of the computer; "devices and printers" or "printers and faxes", right-click the icon of the printer used and select "printing preferences"->; "maintenance"->; "Epson Status Monitor", there will be a "How to" button in this window when the ink quantity is insufficient or exhausted. Click here to open the window for entering the ID number. Please follow the onscreen instructions.
Note: If the ink indicator is flashing, you can continue to use it until the ink indicator is always on, and then enter the ID number to reset.
2. Non -(L20 1) ink quantity. L 10 1, L80 1) The printer count is an estimated value, which may cause errors with the actual ink quantity due to some operations in actual use.
When the ink lamp is always on, please fill it with ink (it is recommended to fill all four-color ink bins), then press the printer's maintenance key (inverted triangle key) to reset the ink and turn off the ink lamp.
Tip:
Please pay attention to the ink capacity of the ink cartridge. When the ink amount is less than 20 mm, please replenish the ink in time to avoid the failure of the print head.
The ink light is on all the time. If there is no response when pressing the maintenance key, please press and hold the printer's maintenance key (inverted triangle key) and lightly wipe it twice.
If the above scheme still can't solve your problem, please log in to Epson official website "Online Engineer": 219.232.55.146/portal/epson to communicate with Epson engineers in real time and solve the problem in time. (Epson "Online Engineer" service hours: 9: 00- 18: 00 from Monday to Friday)
Question 5: How to ink the printer?
1 Add some points to the printer first. Then the cover is opened, and the ink cartridge automatically moves to a position convenient for taking out. Then press to remove the ink cartridge. (The specific removal method may be related to the printer. Please refer to the printer manual. )
In this example, there are two demonstration ink cartridges, one is a black original ink cartridge (without ink holes) and the other is a three-color ink cartridge (with three ink holes). If the black ink is insufficient, take the black ink, and the corresponding color ink is insufficient to take the color ink cartridge. Here, please explain the two.
When picking up the ink cartridge, prepare a clean piece of paper and put the ink cartridge on it.
There is a tape on the top of each ink cartridge, but there will be holes for injecting ink under the tape. You can see it by gently tearing it (don't throw away the tape after tearing it, and stick it with tape after filling the ink).
4 The purchased ink generally has a pen tip that is convenient for adding ink. Pay attention to adding ink at one time and don't squeeze too much. Because there will be bubbles. This can be done step by step. After adding ink, it is recommended to seal the hole with tape. This can prevent ink from spilling and dust from drifting in. (Generally, the appearance of two or three squares of the ink bottle when the recommended ink quantity is added will be explained according to the size of the ink bottle. )
The original ink cartridge has no ink hole. But you can see a concave point that can be opened by yourself. You need to carefully cut a hole with your own knife. Don't let the plastic fall in the process of opening, and then add ink according to the above (opening it yourself will make the original ink cartridge lose the ability to read the ink amount, but my test will not affect the use)
If it is to replace the continuous supply equipment, it is necessary to go to a special printer sales and maintenance place to replace the continuous supply equipment. Then your task is to give it all to others, so there is no need to explain it.
7 If the printing ink is weak after inking, it is necessary to clean the print head in the settings (not by yourself, but in the settings of the printer driver), and the effect will be improved.
Question 6: How does HP printer print ink? I suggest you don't add color, because it has three modules, namely red, yellow and blue. If you add the wrong color, it will mix up. How can I be satisfied?
Question 7: How to fill the ink cartridge of Epson printer?
Seal the ink outlet of the empty ink cartridge with adhesive tape, and extract 1 color ink from each disposable syringe for injection. Check whether the ink is deteriorated or precipitated under the light, aim at the small holes on the ink cartridge and inject them into the corresponding color units of the ink cartridge respectively. (After the disposable syringe is filled with ink, clean it with pure water and use it next time. ) Never tear off the plastic paper on the ink cartridge to avoid poor sealing and air leakage. Each color of ink has two small holes, and it is best to inject from the latter. There is a sponge in the ink cartridge, and with the increase of ink injection times, the ink absorption capacity of the sponge will decrease (this is the first reason why it is best to fill the ink cartridge directly on the printer). After the ink cartridge is full, seal the needle hole with adhesive tape, tear off the adhesive tape that seals the ink outlet at the same time, and weigh it to see if the ink is filled to 70% or 90%.
Midway inkjet
After printing, it is best to write down the number of photos printed. After printing about 10 A4-sized photos (1270 can print 20 photos), gently remove a locking bolt under the ink cartridge from the paper outlet (1270 directly next to the ink cartridge), (you can see it with a flashlight) move the ink cart out, and open the ink cartridge cover (in this case, the next time you remove the ink cartridge and replace the chip, When the printer shows that there is no ink (in fact, there may be ink in the ink cartridge), it is time to redo steps 2 and 3. If you don't do the first step, you won't do the fourth step, but when the printer shows that there is still ink, it may be that the ink cartridge is out of ink. I don't know when the ink is really used up, which often makes the photos being printed obsolete.
Cold mounted photo
After the photos are printed, they are cold-mounted. A cold-mounted paper for A4 photos is about a few cents, which not only solves the problem of light resistance, but also wipes the dust on the photo surface with a wet towel. Anyway, it has to be cold mounted. You can print photos at home with good quality inkjet paper.
Printing of large format photos
The printer can print out the paper with the length exceeding 1 m at a time, and divide a photo into several copies on the computer. After printing, you can print large-format photos by bonding, cold mounting or coating. I have printed a 2 m X 4 m large format photo, and the effect is clearer than that of a wide format printer.
In short, it is really feasible to print photos with ink! Compared with the original ink cartridge, the quality difference is very small, which is generally difficult to see, and the cost is indeed reduced. However, it must be noted that printing with ink is easy to cause (note that it is "easy to cause" rather than "about to cause") nozzle blockage, which has reached the point where nozzles are scrapped (it may cost hundreds of dollars to replace nozzles), and blind ink injection may not be worth the candle, so novices should pay special attention. For those with poor hands-on ability, small printing volume and abundant hands, it is best to use original or compatible ink cartridges.
In addition:
Epson ink cartridge is separated from the ink cartridge through the nozzle, and only the ink cartridge is replaced after the ink is used up. The spray head is fixed on the printer, and besides being compatible with ink cartridges, it can also be filled with ink at home. Some new Epson printers (870, 875, 680, 790, 890, 895, 1270, 1290, etc. ) Add a small thing to the ink cartridges (color and black ink cartridges), that is, an IC chip to record the remaining amount of ink. If the ink is used up and filled up, it is not necessary to reload the ink cartridge into the printer. It requires both ink cartridges to display ink, because the printer prompts according to the recorded information of the IC chip of the ink cartridge. But if you pry this IC chip open and replace it with a new IC chip, you will still put the ink cartridge in, and the printer will recognize it, even if your ink cartridge is not full! It can't recognize the old IC chip printer installed on the new original ink cartridge. Only Epson knows the real reason for installing this IC chip. In short, the printer recognizes the "core" instead of the "box"! At the same time, it also shows that IC chip can not reflect the real remaining amount of ink. Some consumers complain that Epson ink cartridges do not reflect the real amount of ink when providing the final information of ink. The remaining amount of some inks exceeds 30% of the total capacity. When one color ink cartridge runs out of ink, the whole ink cartridge can't be used any more. Epson didn't publicly prompt and explain that there was ink left in its ink cartridge when it showed that it was short of ink ... >; & gt
Question 8: How to add ink to a Dell printer? Open the top cover, and the car will move the ink cartridge to the middle. You can take out the ink cartridge by hand, throw away the label attached to the ink cartridge and see a small hole. Add it with the inking tool * * *, and it's OK.
Question 9: How to add ink to Canon printer? Canon 1 180 and 1880 printers can add ink ... without taking out the ink cartridge ... I think it is very useful ... I have added it countless times ... This is only for adding black ink ... I hope it can help you. ...
"1" Don't tear the paper. Drill a hole at 830.
The ink bought in "2" comes with its own plug. ..
"3" Stretch the ink bottle with the rubber inflated by the bicycle. It is easy to add ink when it is deformed. Syringes can also be used. One yuan is very simple.
"4" After adding ink, plug it with a plug. ..
After "5", you don't need to take off the inkpad ... Open the lid and add ink directly-OK ... Recently, I left it open without using the plug ... but I don't need to remember to cover the hole for a long time ... otherwise, I will run out of ink. Remember to add less ink. If there are too many ink heads, the ink will flow out ... this method is very practical. ...
Attention, friends who have been printing for a long time .. It is best to have something to do and print about four times a month to prevent the printer ink head from clogging. The printer at home is useless for a month. The printer ink head is seriously blocked .. Deep cleaning 10 times before printing.
Question 10: How to add ink to a pinhole printer is generally not to add ink, but to buy ribbons directly. Very cheap, 10 twenties.