Chevrolet Explorer dashboard display
Chevrolet Explorer Fault Light Graphic Complete Manual
Basic indicators are divided into four categories:
(1) The red indicator light represents a warning, and the owner should check the fault before driving.
(2) The yellow indicator light warns the owner to solve the corresponding fault as soon as possible.
③ The blue indicator light reminds the owner to pay attention to the influence, such as whether turning on the high beam will cause the glare of the opposite vehicle.
④ The green indicator light is a function light, such as width indicator, turn indicator and low beam indicator.
The following is the icon of Chevrolet Explorer indicator light (digital map)
4. Cleaning liquid level
This means that the glass water storage tank should be filled with glass water at this time.
5. Brake friction plate
It shows that the friction plate is seriously worn and invalid. Please note that the friction plate on one shaft should be replaced at the same time.
19. Steering locking system
The steering wheel is locked, indicating that there is something wrong with the steering system. Don't tow the vehicle at this time, it will cause danger.
2 1. Tire inflation pressure monitoring system
There are two reasons: one is that the nail of the tire causes the air pressure to drop or expand, and the other is that the system has not recognized new information after replacing the tire.
3 1. Electromechanical parking brake
Used to monitor whether the electric handbrake works normally. When the parking brake is released, the indicator light must go out. When the indicator light flashes continuously, it means that the handbrake is not in the normal working position and may be in danger of rolling.
32. Battery capacity
The battery is dead.
cooling system
The coolant may be insufficient, or the cooling fan may not work.
49. Anti-lock braking system
When the fault light is on, it means that the anti-lock braking function fails during braking. The EDS fault of the electronic differential system will also cause the fault light to light up. In an emergency, stepping on the brake pedal will cause risks such as sideslip and tail flick.
Fuel stock
When this symbol lights up for the first time, it means there is not much left in the tank. When the fuel is sufficient, it will light up, indicating that the fuel system is faulty.
57. Engine oil level
If the oil pressure is too low or the oil quantity is insufficient, please check the oil level as soon as possible.
60. electronically controlled driving stability system
When the fault light is always on, the ESP function is turned off or invalid. At this point, extreme operation may lead to risks such as tail flick.
62. Exhaust gas monitoring system
One is insufficient fuel combustion, and the other is the failure of three-way catalytic converter.
Chevrolet Explorer Remote Battery Replacement
The original battery of Chevrolet Explorer adopts valta brand. There are differences between different models of batteries, and whether there is an automatic start-stop function will also affect the battery model, so the owner must consult clearly before buying.
Chevrolet Explorer battery replacement tutorial
Location: right side of engine compartment.
1. The battery is located in the engine compartment. Open the hatch cover and find the specific location.
2. Remove the battery end protection and fixing bracket nut.
3. Disconnect the negative connection of the battery, and then remove the positive connection. This is to prevent short circuit, because the negative electrode is connected to the car body.
4. After removing the surrounding fixing devices and positive and negative wires, the battery can be replaced. (Note: When the inclination angle is greater than 40, the electrolyte on the old battery is easy to flow out. )
Note: It is best not to interrupt the battery replacement (it is not recommended for the owner to take risks), otherwise the electronic data recorded in the dashboard will be completely emptied, the owner's daily operating habits and driving data will all be restored to the factory settings, and parameters such as date and time will be reset.
Chevrolet Explorer's Power Course
1. The positive symbol of the battery is+,and the negative symbol is-.
2. The positive wire is connected to the positive port of the battery, and the negative wire is connected to the negative port. (The operation process needs to be carried out in the flameout state. )
3. After starting the vehicle with insufficient power, remove the wires and run the engine for 10-20 minutes, so as to normally store enough power for the battery. Chevrolet Explorer dashboard display schematic Chevrolet Explorer remote battery replacement @20 19