Zhike controller 10 fault

1, fault code 10: When the controller stops working, it is necessary to check whether the rear wheel is stuck; 2. Fault code 1 1: The controller stops working, that is, under-voltage or over-voltage, so it is necessary to check whether the charger is damaged; 3. Fault code 12: The controller stops working, that is, it is overcurrent. If it persists, please contact after-sales service; 4. Fault code 13: The controller stops working, that is, the controller is overheated. Please drive the vehicle to a cool place to avoid violent driving; 5. Fault code 30: Battery overcharge protection, that is, charge saturation protection, and it is necessary to check whether the charger is damaged and whether the charger model is consistent with the corresponding model. Fault code 3 1: charging over-current protection, that is, charging saturation protection, and it is necessary to check whether the designated vehicle type uses batteries; 7. Fault code 32: Low-temperature charging is prohibited, that is, it is less than 30s and less than-20℃ for 3 s. Please put the battery indoors and recover itself when the battery temperature is higher than 3℃. 8. Fault code 60: Communication module failure, that is, SIM card identification failed. Please contact after-sales service; 9. Fault code 62: Communication module fault, that is, GPS fault, please contact after-sales service; 10, fault code 63: communication module fault. That is, the GPS antenna is short-circuited, please contact after-sales service; 1 1, fault code 64: communication module fault. Which means the GPS antenna is on. Please contact after-sales service; 12, fault code 65: communication module fault, that is, vehicle SN and central control serial number are not written (flashing), please contact after-sales service; 13, fault code 67: communication module fault, that is, the SIM card is in arrears (displayed for 2 seconds), please contact after-sales service; 14, fault code 99: communication bus fault. That is, central control fault and bus fault, please contact after-sales department: 15, fault code 1 10: controller fault, that is, power tube fault and drive power supply fault, please contact after-sales department; 16, fault code11:the controller calibration failed, that is, the controller is illegal, and the controller is invalid, so it is necessary to check whether the non-original controller is used; 17, fault code 120: motor fault, that is, Hall fault and phase loss, please contact after-sales service; 18, fault code 130: battery overdischarge alarm, that is, the battery is about to run out, BMS is about to enter overdischarge protection, so use charger to charge the battery; 19, fault code 13 1: discharge overcurrent alarm, that is, the battery current reaches the protection value, and BMS is about to perform overcurrent protection. Please check whether the battery is used in the specified model. If it continues to appear, please contact after-sales service; 20. Fault code 132: battery overtemperature alarm, that is, the battery temperature is about to reach the protection value, and BMS is about to enter overtemperature protection. Please take out the battery and put it in a cool place. When the battery core cools to below 60℃, it can be used again. ; 2 1, fault code 133: low-temperature charging and discharging is prohibited, that is, the battery is below -20℃ for five consecutive seconds. When the temperature is higher than-15℃, please take out the battery and use it again; 22. Fault code 140: Steering handle fault. That is, there is something wrong with the handle. Please contact after-sales service: 23. Fault code 190: communication fault of the controller, that is, the controller has no returned data, please contact the after-sales service; 24. Fault code 19 1: battery communication fault. That is, the battery does not return data or data errors. Please check whether the battery plug is tightened. If it continues to appear, please contact after-sales service. ; 25. Fault code 16 1: Rotating handle is faulty. That is, the handle is out of order, please contact after-sales service; 26. Fault code 190: Communication fault of the controller, that is, the controller fails to return data or data errors for 15 consecutive times, please contact the after-sales service; 27. Fault code 19 1:BMS communication fault, that is, BMS failed to return data or data errors for 15 times in a row. Please check whether the battery plug is tightened. If it continues to appear, please contact after-sales service.